Position: Home > Circuit Diagram > Index 1836
Low Cost Custom Prototype PCB Manufacturer

Circuit Diagram

Index 1836

The computer ECU outlet sequence table of Xiali EFI TJ37100E

Published:2011/5/20 10:25:00 Author:Borg | Keyword: ECU, outlet sequence, Xiali

The computer ECU outlet sequence table of Xiali EFI TJ37100E
The computer ECU outlet sequence table of Xiali EFI TJ37100E

The internal functions of computer ECU is listed here. Of the input signals, the engine rotating speed and car speed signals are impulse, and they will be put into timers after passing the shaping circuit; all idling speed signals and equipment load signals and stating signals are generated by their own sensors(or their own switches). And all the admission MAP, water temperature signals and idling speed CO regulator signals are analog impulse. The executing parts mainly consist of igniting coil, oil injector, idling speed raising valve and fuel pump relay, and so on.   (View)

View full Circuit Diagram | Comments | Reading(512)

The electric control system sensor circuit of Xiali EFI TJ37100E

Published:2011/5/20 9:21:00 Author:Borg | Keyword: electric control system, Xiali

The electric control system sensor circuit of Xiali EFI TJ37100E
The electric control system sensor circuit of Xiali EFI TJ37100E

The following table represents the functions, position and principle features of the input signal sensors in the electric control system.   (View)

View full Circuit Diagram | Comments | Reading(428)

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (3)

Published:2011/5/20 20:27:00 Author:Borg | Keyword: petrol injection, Tianjin Xiali

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (3)
30-instrument board lamp; 31-width lamp; 32-tail lamp; 33-fuse; 34-starter; 35-air-conditioning control; 36-warm air motor fuse; 37-air-conditioning pressure switch; 38-warm air motor; 39-speed governing; 40-warm air motor switch; 41-water temperature sensor; 42-compressor magnetic clutch; 43-condenser fan relay; 44-condenser fan motor   (View)

View full Circuit Diagram | Comments | Reading(1018)

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (2)

Published:2011/5/20 20:14:00 Author:Borg | Keyword: petrol injection, Tianjin Xiali

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (2)
20-admission MAP sensor; 21-shielded wire; 22-engine rotating speed and steering angle sensor(in the electricity distributor); 23-test terminal; 24-igniting coil; 25-shielded coil; 25-defroster fuse; 26-defroster switch; 27-rear window defroster; 28-tail lamp switch; 29-tail lamp fuse; 30-instrument lamp; 31-width lamp; 32-tail lamp; 34-starter; 35-air-conditioning amplifier; 36-warm air motor fuse; 41-water temperature sensor;   (View)

View full Circuit Diagram | Comments | Reading(732)

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (1)

Published:2011/5/20 20:05:00 Author:Borg | Keyword: petrol injection, Tianjin Xiali

The petrol injection engine circuit of Tianjin Xiali EF1 TJ376Q-E (1)
1-battery; 2-cooling fan fuse; 3-igniting switch fuse; 4-igniting switch; 5-engine fuse; 6-pre- power supply fuse; 7-e-control petrol injection system fuse; 8-e-control petrol injection relay (the chief relay); 9-oil injector; 10-engine ECU; 11-instrument board fuse; 11a-throttle position sensor(idling speed sensor); 12-engine fault alarm lamp; 13-speed sensor; 14-idling speed raising valve; 15-cooling fan relay; 16-cooling fan motor;   (View)

View full Circuit Diagram | Comments | Reading(734)

The electric controlled oil injection system circuit of Tianjin Xiali TJ376Q-E

Published:2011/5/20 11:06:00 Author:Borg | Keyword: oil injection system, Tianjin Xiali

The electric controlled oil injection system circuit of Tianjin Xiali TJ376Q-E
The TJ376Q-E electric controlled oil injection system belongs to a speed-density(D) oil multiple points injecting engine, whose main ingredients are as shown in Figure 5-1. Like other petrol injecting engine, it consists of admission system, oil supply system and electric control system.1.admission systemThe air comes through the filter(5) to remove the dust, and then goes past the throttle body(11) and the throttle and into the balance box(15) where it is re-distributed into each admission cylinder. When the admission valve is open, the air is inhaled into the cylinder with the petrol.   (View)

View full Circuit Diagram | Comments | Reading(958)

The circuit of Tianjin Xiali TJ710OE

Published:2011/5/20 3:41:00 Author:Borg | Keyword: circuit, Tianjin Xiali

The circuit of Tianjin Xiali TJ710OE
The new EFI of Tianjin Xiali started to be produced by DAZE Automobile Industry in 1997, it improved on 710OU. In TJ710OE, the engine is the TJ376Q-E e-control petrol injection engine,and the 710OU is fixed with the TJ376Q carburetor engine. After a lot of times of trials, we finally succeeded, and the car war launched to the market. The outline of the car has been improved, but the body and the chassis are almost the same with the former model. It it three-box, four-door and five-chairs, the maximum speed is more than 140km/h, the oil consumption at stable speed(60km/h) is less than 4.2L which is conforming to ECEl5-04. In a word, all the indexes are better than the former TJ710OU and TJ7100.   (View)

View full Circuit Diagram | Comments | Reading(496)

The air-conditioning control circuit of Xiali TJ7100.7100U

Published:2011/5/20 10:07:00 Author:Borg | Keyword: air-conditioning, control circuit, Xiali

The air-conditioning control circuit of Xiali TJ7100.7100U
The air-conditioning control circuit of Xiali TJ7100.7100U

The cooling tube system of Xiali is seen in Figure 1, in the room, the cooling evaporator absorbs heat so that the refrigerant RI2 evaporates, the evaporant is in the condition of low-pressure(about 0.2 MPa) and low-temperature(about O℃) now. When RI2 converts from liquid in to gas, it has absorbed a lot of heat of vaporization, then the steamed RI2 flows into the cylinder, and it is turned into liquid again after pass the piston, but the temperature and pressure raises a lot(temperature is about 60-70℃ , pressure is between 1·0-1·5Mpa), and it is strained from the compressor to the condenser.   (View)

View full Circuit Diagram | Comments | Reading(511)

The steering and danger signal, lighting and headlight circuit of Tianjin Xiali TJ7100.7100U

Published:2011/5/20 20:40:00 Author:Borg | Keyword: steering, headlight, Tianjin Xiali

The steering and danger signal, lighting and headlight circuit of Tianjin Xiali TJ7100.7100U
48-steering and danger warning switch; 49-steering flash; 50-left steering indicator; 51-left steering signal lamp(head, side,rear); 52-right steering indicator; 53-right steering signal lamp(head, side and rear); 54-loudspeaker; 55-loudspeaker key; 56-switch lamp; 57-head width lamp; 58-license lamp; 59-rear width lamp; 60-light switch; 61-instrument lighting lamp; 62-left head light; 63-right head light; 64-high beam indicator; 65-dimmer switch and overtaking signal switch   (View)

View full Circuit Diagram | Comments | Reading(450)

AN6210-The integrated circuit of dual recording/producing preamplifier

Published:2011/5/19 21:11:00 Author:Borg | Keyword: preamplifier circuit

AN6210-The integrated circuit of dual recording/producing preamplifier
AN6210-The integrated circuit of dual recording/producing preamplifier
AN6210-The integrated circuit of dual recording/producing preamplifier
AN6210-The integrated circuit of dual recording/producing preamplifier

1.the internal circuit and pin functions of AN6210AN6210 contains two lines of microphone amplifiers, two lines of reproducing preamplifiers, two lines of wiring amplifiers and auto gain control lines. In Figure 1 is the internal circuit of it. Comparing with other circuits, its chief advantages are that the wiring amplifiers are public but the recording/reproducing pre-stage is not, and it is divided into an independent reproducing preamplifier and microphone amplifier. AN6210 is in 28-lead dual in-line package. 2. Principle parameters of AN6210   (View)

View full Circuit Diagram | Comments | Reading(1396)

The instrument, indicator and alarm lamp of Daewoo Racer

Published:2011/5/21 3:09:00 Author:Borg | Keyword: instrument, alarm lamp, Daewoo Racer

The instrument, indicator and alarm lamp of Daewoo Racer
The H7 signal of engine rotating speed comes from the junior negative point of the igniting coil(connecting to igniting module); both the oil meter(H9) sensor and oil alarm switch are fixed in the oil tank, when the oil drops the minimum, the alarm lamp (E45) is on, but the car can run another 50KM. The water temperature meter(H8) and oil tank (H) share a stabilizer whose output voltage is 10V. The sensor parameters of these two meters are seen in Figure 6. One terminal of the electrooptical indicator(E36) connects to F13(No.15 wire), and the other connects with the juncture of the generator diode and the field coil.   (View)

View full Circuit Diagram | Comments | Reading(543)

the air-condtioning circuit of Daewoof Racer

Published:2011/5/21 3:25:00 Author:Borg | Keyword: air-condtioning, Daewoof Racer

the air-condtioning circuit of Daewoof Racer
(11)the air-conditioning circuitAll the air-conditioning system is under the control of the switch S23. When it is at the OFF gear, the circuit is cut off, there is no heating or cooling. HEAT gear means the interior air is heated but not cooling. VENT gear means ventilation, there is no heating or cooling. DEF means defrost, the heater blows warm air to the windscreen, and the cooling system also can be turn on to dry the interior air(the temperature is auto controlled); BL-LEV gear means two levels of air is to be cooled or heated. NORN means normally cooling.   (View)

View full Circuit Diagram | Comments | Reading(604)

The oil injection control system and igniting system circuit of Daewoo-ESPERO

Published:2011/5/20 21:59:00 Author:Borg | Keyword: oil injection, control system, igniting system

The oil injection control system and igniting system circuit of Daewoo-ESPERO
See as Figure 3. the oil injection control system components of Daewoo-ESPERO The   (View)

View full Circuit Diagram | Comments | Reading(490)

The oil injection control system circuit of Daewoo-ESPERO

Published:2011/5/20 10:50:00 Author:Borg | Keyword: oil injection, control system, Daewoo-ESPERO

The oil injection control system circuit of Daewoo-ESPERO
The oil injection control system circuit of Daewoo-ESPERO

The connecting control relationship between oil pump relay, single point oil inject and the computer is shown in Figure 3. And the relationship between all the sensors, idling speed control valve(IAC) and ECU is shown in Figure 4.In figure 3, the ECM is the computer, the A1~A12、B1~B12、C1~C16 and D1~D16 on the border of ECM represent the plugs of a 24-lead A-B and a 32-lead C-D.The wire code consists of 4 parts, for example, between the pin ECMA1 and the pin 86 of oil pump relay, the No.465GNWSO.75 wire means the basic color of NO.465 wire is green, and it is with white strips, the cross-sectional area of wire core is 0.75m㎡.   (View)

View full Circuit Diagram | Comments | Reading(1657)

The control system sensor, fault diagnosis outlet and idling speed control circuit of ESPERO

Published:2011/5/20 21:53:00 Author:Borg | Keyword: control system, fault diagnosis outlet, idling speed control

The control system sensor, fault diagnosis outlet and idling speed control circuit of ESPERO
The connection of the computer with igniting module, igniting coil, test coil(electricity signal generator) is seen in Figure 6.Notes: engine rotating speed is lower than 400rpm, EST connects with the earth, EST has no additional voltage; engine rotating speed is more than 400r/m, EST has additional reference voltage of 5V, EST has a control signal voltage delivered by ECM.Daewoo is fixed with computer controlled e-igniting system, the system has a electricity distributor but no touch spot. When the engine starts, the test coil got a crank position and engine rotating signal, and igniting module delivers the signal to ECM computer.   (View)

View full Circuit Diagram | Comments | Reading(718)

The single oil injection equipment (throttle body injection TBI) circuit of ESPERO

Published:2011/5/20 21:36:00 Author:Borg | Keyword: oil injection equipment, throttle body, ESPERO

The single oil injection equipment (throttle body injection TBI) circuit of ESPERO
1-air filter gasket; 5-oil inlet pipe nut of O shape; 6-oil outlet pipe nut of O shape; 10-flange gasket; 20-oil calculating components; 21-oil calculator fixing screw and gasket; 25-oil calculator to throttle gasket; 35-oil injector fixing screw; 36-spring seat; 66-pressure adjusting spring; 70-pressure adjustment valve component; 90-oil inlet nut; 91-oil pipe nut gasket; 96-oil outlet nut; 200-throttle body components.   (View)

View full Circuit Diagram | Comments | Reading(2182)

The igniting system control circuit of Daewoo

Published:2011/5/20 9:40:00 Author:Borg | Keyword: igniting system, control circuit

The igniting system control circuit of Daewoo
See as figure 6. the igniting system control circuit of Daewoo   (View)

View full Circuit Diagram | Comments | Reading(717)

The principle signal circuit of Daewoo Racer

Published:2011/5/21 21:47:00 Author:Borg | Keyword: signal circuit, Daewoo Racer

The principle signal circuit of Daewoo Racer
The backup lamp switch(S8) controls the lamp of E19 and E20, the turn lamp switch controls the left-hand signal lamps(E21 and E22) and left-hand turn indicator(E39), or right-hand signal lamps(E23 and E24) and right-hand indicator E40(see as instrument indicator). At the moment, the current of flash(K5) is provided by fuse F8 of No.15 circuit and controlled by the igniting switch. If the warning signal is delivered, the alarm lamp switch S9 is supposed to be press, and the current comes from No.30 circuit (positive pole of the battery) directly, so the left and right turn lamps flash at the same time, the flashing frequency is requested to be 85±10times/min.   (View)

View full Circuit Diagram | Comments | Reading(1195)

The principle parameter circuit of Daewoo sensor

Published:2011/5/20 22:19:00 Author:Borg | Keyword: principle parameter, Daewoo

The principle parameter circuit of Daewoo sensor
The principle parameter circuit of Daewoo sensor   (View)

View full Circuit Diagram | Comments | Reading(503)

The oil injection and air-conditioner control circuit of Daewoo-ESPERO

Published:2011/5/20 21:22:00 Author:Borg | Keyword: oil injection, air-conditioner, Daewoo-ESPERO

The oil injection and air-conditioner control circuit of Daewoo-ESPERO
The connection of ECM with magnetic clutch, air-conditioner cooling fan and high-low voltage switch is as shown in Figure 7. The voltage values of computer connectors are listed in Table 13-4, and the test position of the pins are shown in Figure 8. Notice the positions of A1~A12,B1~B12,C1~C16 and D1~D16.In the upper of the figure shows the pin sequence code, wire colors and voltage of plugs A-B, the left upper is pins of A1~A12, right upper is pins of B1~B12; in the lower part of the figure shows the pin sequence code and wire colors of C-D, and the left lower is pins of c1~D16.   (View)

View full Circuit Diagram | Comments | Reading(1490)

Pages:1836/2234 At 2018211822182318241825182618271828182918301831183218331834183518361837183818391840Under 20