The fruits and vegetables detoxification machine

Published:2011/9/8 6:16:00 Author:Ariel Wang | Keyword: fruits, vegetables, detoxification

The fruits and vegetables detoxification machine uses ozone to do the sterilization and degradation on the pesticides remainings in fruits and vegetables.The circuit is made up of power supply circuit,electronic timer, relay-driven circuit,air pump,high voltage generator and ozone generator.The AC220V commercial power gives power supply to the air pump and high voltage generator.It is reduced by T1,commutated by VD1～VD4,filtered by C1.Then it generates about 12V DC voltage for the use of relay-driven circuit.The 12V voltage is regulated by KA78L05 through IC1.Then it forms 5V steady voltage for electronic timer circuit.   (View)

View full Circuit Diagram | Comments | Reading(1561)

the acupoint detector composed of 555

Published:2011/9/8 6:16:00 Author:Ariel Wang | Keyword: acupoint detector

It is the acupoint detector circuit.The acupoint detector is made up by the detecting electrode A and B,multivibrator and acoustic-optic indicator. The oscillator composed of IC1,R8,R9 and C1 output the signal(square wave).The signal is controlled by the oscillator composed of IC2,R11,R12 and C3.Because the impedances in acupoint and non-acupoint act differently in human beings.The circuit converts the impendances to different potentials. The oscillation frequency of the oscillator emits different acoustic-optical signals.In this way,it realizes the acupoint detection.   (View)

View full Circuit Diagram | Comments | Reading(1156)

The regulator: DC-DC circuit and power supply monitor pin and its main features DS2437S

Published:2011/8/30 2:29:00 Author:Seven | Keyword: regulator, power supply, monitor pin

DS2437S—the intelligent cell monitorOnly one pin is for communication; each componenthas a unique 64-bit serial number; it can detect the cell temperature, the precision is ±2℃; the thermometer resolution is 13 bit; the test range is -40~+85℃; it contains a 10-bit A/D converter; a 10-bit cell current A/D converter; it has a time counter(the unit is S); it has 40 byte non-easily lost EEPROM. The definition of the pins are as follows: DQ: data input/output (connected with the host); X1 and X2:the crystal oscillating input; VDD: the cell voltage.   (View)

View full Circuit Diagram | Comments | Reading(494)

Buick GL8 Car ABS Serial Data,SP205,Dynamical System ECU PCM And Other ECU Circuit

Published:2011/8/23 22:06:00 Author:Robert | Keyword: Buick, ABS, Serial Data, Dynamical System, ECU, PCM

The picture shows the Buick GL8 car ABS serial data, SP205, dynamical system ECU PCM, car body ECU BCM, combination instrument, ABS ECU, traction ECU EBCMEBTCB circuit.   (View)

View full Circuit Diagram | Comments | Reading(1381)

The regulator: DC-DC circuit and power supply monitor pin and its main features DS1705/DS1706

Published:2011/8/30 2:31:00 Author:Seven | Keyword: regulator, power supply, monitor pin

The DS1705/DS1706 monitorThe working voltage is 3.3V/5.0V; it has the halt and restart failure micro-processor; it can restart the micro-processor automatically after the computer fault is gone; it has the external overload monitor key; the 3.3V system can exactly monitor the resetting of 5%VCC, 10%VCC and 20%VCC; the 5.0V can monitor the resetting of 5%VCC or 10%VCC. The working temperature range is -40~85℃; the is compatible with MAX705/MAX706 completely. The definitions of its main pins are as follows: PBRST: input by pressing the reset key; IN: input; ST: triggering input.   (View)

View full Circuit Diagram | Comments | Reading(617)

The regulator: DC-DC circuit and power supply monitor pin and its main features DS1632

Published:2011/8/30 2:26:00 Author:Seven | Keyword: regulator, power supply, monitor pin

DS1632--the power supply fault and reset controllerThe working voltage is 5.0V; the computer power supply fault detector; there is a 32.768kHz oscillator on the chip; the clock is coupled with a cell; by pressing the reset key, the input can be done; the monitor precision is 5%VCC or 10%VCC; the reset pulse width is 95ms or 190ms; all the resetting, power supply fault and cell low-voltage are coupled with the additional output. The definitions of the pins are as follows: PBRST: input by pressing the reset key; X1 and X2: the crystal oscillator.   (View)

View full Circuit Diagram | Comments | Reading(528)

The regulator: DC-DC circuit, power supply monitor pin and its main features DS1231S

Published:2011/8/30 2:24:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

The DS1231S power supply monitorThe working voltage is 5.0V; when the power supply fault is approaching, it will send the forecast to the processor; it provides the power failure lasting time; it can automatically restart the processor when the power is coming; the monitor precision is 5%Vcc or 10%Vcc; it can adjust the maintenance time of power saving; it can replace the power reset circuit. The main pins of it are as follows: IN: input; MODE: pin features selecting; TOL: choosing detection of 5%Vcc or 10%Vcc.   (View)

View full Circuit Diagram | Comments | Reading(506)

The regulator: DC-DC circuit, power supply monitor pin and its main features BA6122A/6122AF

Published:2011/8/24 21:51:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

BA6122A/6122AF--The switch stabilizer control circuit (dual output) This is a switch stabilizer control circuit of dual output, which forms the 5V or 9V dual output switch stabilizer; it contains a 5V Vref circuit, sawtooth wave oscillating circuit, fault amplifier circuit, comparing circuit and output circuit; the working power supply voltage range is 8~16V; The 9V system has the stopping function; the drive load ratio changing range of the driver is 0~100%; the power consumption is 340mW; the working temperature is -10~+60℃.   (View)

View full Circuit Diagram | Comments | Reading(660)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN8360NK

Published:2011/8/24 21:50:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AN8360NK voltage charge control circuit This is a control circuit of the lead battery fast charging current; it can quickly charge the 4~12V lead battery (about 80min); the working voltage range is 8~19V; the charge reference signal is generated by 8-bit A/D converter; the max power supply voltage is 20V; the max power supply current is 33mA; the power consumption is 660mW; the working temperature is -20~75℃.   (View)

View full Circuit Diagram | Comments | Reading(696)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN8060

Published:2011/8/24 21:50:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AN8060--the 4V stabilizer (with reset terminal) This is a stabilizer with the fixed output voltage; the output voltage is -4V; the max output current is 30mA; the minimum input-output voltage difference is lower than 0.2V; the input voltage range is -12~0.3V; the power consumption is 500mW; the working temperature is -20~+75℃; it contains the test comparator.   (View)

View full Circuit Diagram | Comments | Reading(804)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN8050S

Published:2011/8/24 21:49:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AN8050S stabilizer (multiple input) This is a stabilizer of multiple input whose output voltage is fixed; the output voltage includes two teams of tracking voltages, which are ±5V and -4.3V; the output current of ±5V is +80mA, the output current of +5V is +50mA, and the output current of -4.3V is +10mA; the working power supply voltage range is ±2~±9V; the power consumption is 420mW; the working temperature is -20~+75℃; it contains the decompression test comparator and heat protection circuit.   (View)

View full Circuit Diagram | Comments | Reading(563)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN6541

Published:2011/8/24 21:48:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin, main features

AN6541 the 3-terminal regulator This is a 3-terminal regulator whose output voltage is fixed; the output votlage is 9V; output current is 300mA; the typical voltage difference value between minimum output and input is 0.3V; the output voltage temperature coefficient is ±0.01%℃; maximum input voltage is 20V; power consumption is 15W; working temperature is -30~+80℃; it contains output current limiting protection circuit.   (View)

View full Circuit Diagram | Comments | Reading(556)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN6540

Published:2011/8/24 21:47:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AN6540 the step-up time adjustable regulator (forward input) This is a 4-terminal stabilizer whose output voltage is stable and step-up time is adjustable; the output voltage is 8.5V; the minimum input and output voltage difference typical value is 0.3V; the maximum voltage is 20V; the working temperature is -30~+80℃; it contains output current limiting protection circuit.   (View)

View full Circuit Diagram | Comments | Reading(720)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN5905

Published:2011/8/24 21:47:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

This is a switch stabilizer control circuit; its oscillating frequency can be doubled or quadrupled; it contains the soft starting circuit; the max power supply voltage is 14.4V; power consumption is 230mW; the working temperature is -20~+70℃; it contains the over-current protection circuit.   (View)

View full Circuit Diagram | Comments | Reading(558)

The regulator: DC-DC circuit, power supply monitor pin and its main features AN900

Published:2011/8/24 21:47:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AN900--the switch stabilizer control circuit This is a switch stabilizer control circuit which contains a soft starting circuit; the duty cycle is 0~0.7; it can be triggered externally; the Vref depends on the external Zener diode; the max power supply voltage is 14.4V; the max power supply current is 18mA; the working temperature is -20~+75℃; it contains the over-voltage, over-current, high power supply voltage, low power supply voltage and other protection circuit.   (View)

View full Circuit Diagram | Comments | Reading(644)

The regulator: DC-DC circuit, power supply monitor pin and its main features AD581

Published:2011/8/24 21:46:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

AD581 reference voltage circuit (+10V) This is a wide-band 3-terminal Vref circuit; its output voltage is 2.5V; the output voltage is 10V; the primary fault of AD581L/581U output voltage is ±5mV; When it is 0~70℃, the temperature drift of AD581L is 5*10-6/℃, when it is -55~+125℃, the temperature drift of AD581U is 10*10-6/℃; the long-term stability is 25*10-6/1000h; the input voltage range is 12~40V; the output current is 10mA; the -10V Vref power supply can be the 2-terminal Zener diode; when the environment temperature is lower than 25℃, the power consumption is 600mW.   (View)

View full Circuit Diagram | Comments | Reading(549)

The regulator: DC-DC circuit, power supply monitor pin and its main features 7800

Published:2011/8/24 21:44:00 Author:Seven | Keyword: DC-DC circuit, power supply, monitor pin

7800 serial 3-terminal stabilizer (forward output) This is a 3-terminal stabilizer whose output voltage is stable; the output voltages are 5V, 6V, 7V, 8V,9V,10V,V12V,15V, 18V, 20V and 24V; output current is 1A; the output voltage range is 5~18V; the maximum output voltages are 35V, 20V 24V and 40V respectively; the working temperature of 7800 is -55~150℃, and the 7800C working temperature is 0~+125℃; it contains the over-current limitation and secure working area protection circuit. The approaching modes are μA7800, LM7800, MC7800, HA7800P, μPC7800M, NJM7800, TA7800AP, AN7800 and CW7800.   (View)

View full Circuit Diagram | Comments | Reading(545)

Grain Moisture Tester

Published:2011/9/3 22:39:00 Author:Ariel Wang | Keyword: Grain, Moisture

A, B are two measuring electrodes. As the resistance value of food is generally high.Even during the measurement electrode with high voltage of about 150V, the current between two electrodes is only less than 1μA.The value of the measurement should be amplified by IC1 Integrated operational amplifier 5G3140 and then it could be indicated by header M. The higher the grain moisture content, the greater the current between the electrodes A and B , the greater the value the meter indicates. The pulse oscillator is made up of IC2's Time-base circuit 555.It is stepped up by transformer T,commutated by the diode.Then it generates 150V high voltage for the measurement of the electrodes.   (View)

View full Circuit Diagram | Comments | Reading(3339)

The electronic voltmeter of LED display

Published:2011/9/2 3:00:00 Author:Ariel Wang | Keyword: electronic , LED display

The circuit consists of 6 LEDs,two integrated circuits and some resistors.It could display the storage battery's voltage value of the motors,cars and electric bicycles .It is very convenient to use.   (View)

View full Circuit Diagram | Comments | Reading(641)

The home points electrotherapy

Published:2011/9/3 23:48:00 Author:Ariel Wang | Keyword: home , points

There are many different types of electronic treatment in the medical device market.They are said that they have a special effect to certain diseases.The price is also not cheap. In fact, most of them are nothing more than some electronic treatment devices which can output some pulses .They may have the effect to some diseases in accordance with different frequencies of the output pulse waveform.It is the home points electrotherapy shown as the chart. The whole circuit is mainly composed of a Schmitt trigger CD40106 six.The ultra-low-frequency multivibrator oscillation consists of the Dl, Rl, VDl and C1. The oscillation frequency is 0.5 ~ 5Hz. It is regulated by RPl.   (View)

View full Circuit Diagram | Comments | Reading(1776)

Pages:15/164 1234567891011121314151617181920Under 20