Published:2012/12/13 21:31:00 Author:muriel | Keyword: Feedback amplifiers
View full Circuit Diagram | Comments | Reading(712)
Published:2012/12/13 21:29:00 Author:muriel | Keyword: Audio Amplifier
View full Circuit Diagram | Comments | Reading(0)
Published:2012/12/13 21:27:00 Author:muriel | Keyword: XTal Filter, RF Amplifier
View full Circuit Diagram | Comments | Reading(1380)
Published:2012/12/12 21:21:00 Author:muriel | Keyword: cascode , BJT , RF amplifier
View full Circuit Diagram | Comments | Reading(2686)
Published:2012/12/12 21:19:00 Author:muriel | Keyword: Variable Q1, Emitter Degeneration
View full Circuit Diagram | Comments | Reading(690)
Published:2012/12/12 21:19:00 Author:muriel | Keyword: Q1, Q2, bias version
View full Circuit Diagram | Comments | Reading(684)
Published:2012/12/12 21:18:00 Author:muriel | Keyword: fixed bias version
View full Circuit Diagram | Comments | Reading(627)
Published:2012/12/12 21:17:00 Author:muriel | Keyword: cascode , 2N3904, IF amplifier
View full Circuit Diagram | Comments | Reading(4270)
Published:2012/12/12 21:17:00 Author:muriel | Keyword: cascode amplifier
View full Circuit Diagram | Comments | Reading(0)
Published:2012/12/12 21:14:00 Author:muriel | Keyword: Cascode, BJT, RF Amplifier
View full Circuit Diagram | Comments | Reading(2620)
Published:2012/12/12 21:13:00 Author:muriel | Keyword: 5 MHz , WWV Cascode, Bipolar Amplifier
View full Circuit Diagram | Comments | Reading(942)
Published:2012/12/12 21:11:00 Author:muriel | Keyword: Tuning, Whip, Other Frequencies
View full Circuit Diagram | Comments | Reading(634)
Published:2012/12/12 21:10:00 Author:muriel | Keyword: broadband version, W7ZOI
The broadband version W7ZOI suggested to try building. I modified the output transformer in the Figure 6 project and tested it with Tom, VE7TW. We really liked it. By adjusting the network trimmer capacitor, I was also able to tune the 30 meter Amateur radio band as well. For 30 meter band use, I peaked the tank circuit at 10.125 MHz by listening to receiver noise with a home brew direct conversion receiver and was suitably impressed.
This is the active antenna design I wll use for my future projects where strong voltage gain is required. If your receiver has a higher impedance such as 500 ohms, you might try using a couple more links on the output transformer secondary winding.
(View)
View full Circuit Diagram | Comments | Reading(2833)
Published:2012/12/12 21:09:00 Author:muriel | Keyword: Cascode JFET Amplifier
View full Circuit Diagram | Comments | Reading(1292)
Published:2012/12/12 21:09:00 Author:muriel | Keyword: Common Gate Amplifier
View full Circuit Diagram | Comments | Reading(1178)
Published:2012/12/12 21:08:00 Author:muriel | Keyword: Tuned Whip
Previous experimentation confirmed that it is easy to tune a short whip antenna by connecting it to the hot end of an L C (inductor and capacitor) tank circuit. The high impedance whip antenna was matched to a JFET RF amplifier by placing a high value (1 megohm or greater) on the JFET gate to ground. Although this method is practical, I desired a network to transform the output impedance of the tuned whip tank tank circuit to a known impedance. I do not possess the knowledge or mathematical skill to design such a network and asked Wes Hayward if he might consider doing this for me. My desired parameters for the network were 10.0 MHz, a 50 ohm output impedance and a 4 foot (122 cm) whip. Please refer to Wes' calculations and schematic in Figure 2 below. This math is difficult, however, a practical design for experimentation is provided. (View)
View full Circuit Diagram | Comments | Reading(628)
Published:2012/12/12 21:07:00 Author:muriel | Keyword: experimental , broadband , cascode, JFET VPA
Many builders emailed me requesting a simple, broadband VPA (voltage probe antenna) design with more power gain than the common gate versions I have presented elsewhere on this web site. Connecting a whip antenna to a cascode JFET stage described by W7ZOI in Experimental Methods in RF Design is 1 method I considered.
I built the version shown in Figure 1 almost 2 years ago. This VPA. although more powerful, overloaded the front end of my test receiver with multiple RF signals. Clearly some tuning on the input was needed.
(View)
View full Circuit Diagram | Comments | Reading(1187)
Published:2012/12/12 2:32:00 Author:Ecco | Keyword: dual JFET , input op amp, main characteristics
Input offset voltage is 10mV ; temperature drift is 75μV / ℃; bias current is 2pA ; Gain Bandwidth Product GB = 1MHz; conversion rate is 6V/μs ; Current consumption is 4.5mA ; power supply is ± 18V; differential input voltage is ± 30V ; common-mode input voltage is ± 15V; power consumption is 500mW.
(View)
View full Circuit Diagram | Comments | Reading(1171)
Published:2012/12/12 0:40:00 Author:muriel | Keyword: 50 Watt, Amplifier
View full Circuit Diagram | Comments | Reading(0)
Published:2012/12/12 0:39:00 Author:muriel | Keyword: 8 Watt, Audio Amp
View full Circuit Diagram | Comments | Reading(639)
Pages:34/250 At 202122232425262728293031323334353637383940Under 20 |