ZNBG3113, ZNBG3113A, ZNBG3113Q20 Selling Leads, Datasheet
MFG:ZETEX Package Cooled:SOP20 D/C:99
ZNBG3113, ZNBG3113A, ZNBG3113Q20 Datasheet download
Part Number: ZNBG3113
MFG: ZETEX
Package Cooled: SOP20
D/C: 99
MFG:ZETEX Package Cooled:SOP20 D/C:99
ZNBG3113, ZNBG3113A, ZNBG3113Q20 Datasheet download
MFG: ZETEX
Package Cooled: SOP20
D/C: 99
Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
TOP
PDF/DataSheet Download
Datasheet: ZNBG3113
File Size: 700842 KB
Manufacturer: ZETEX [Zetex Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: ZNBG2000
File Size: 526974 KB
Manufacturer: ZETEX [Zetex Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: ZNBG3113Q20
File Size: 700842 KB
Manufacturer: ZETEX [Zetex Semiconductors]
Download : Click here to Download
The ZNBG series of devices are designed to meet the bias requirements of GaAs and HEMT FETs commonly used in satellite receiver LNBs, PMR cellular telephones etc. with a minimum of external components.
With the addition of two capacitors and a resistor the devices provide drain voltage and current control for three external grounded source FETs, generating the regulated negative rail required for FET gate biasing whilst operating from a single supply. This negative bias, at -3 volts, can also be used to supply other external circuits.
The ZNBG3113/14 includes bias circuits to drive up to three external FETs. A control input to the device selects either one of two FETs as operational, the third FET is permanenly active. This feature is particularly used as an LNB polarisation switch. Also specific to LNB applications is the 22kHz tone detection and logic output feature which is used to enable high and low band frequency switching.
The facility to control the tone switching delay is provided. This allows the rejection of other lower frequency tones tat may be present in multiple LNB applications.
Drain current setting of the ZNBG3113/14 is user selectable over the range 0 to 15mA, this is achieved with addition of a single resistor. The series also offers the choice of drain voltage to be set for the FETs, the 3113 gives 2.2 volts drain whilst the 3114 gives 2 volts.
These devices are unconditionally stable over the full working temperature with the FETs in place, subject to the inclusion of the recommended gate and drain capacitors. These ensure RF stability and minimal injected noise.
It is possible to use less than the devices full complement of FET bias controls, unused drain and gate connections can be left open circuit without affecting operation of the remaining bias circuits.
To protect the external FETs the circuits have been designed to ensure that, under any conditions including power up/down transients, the gate drive from the bias circuits cannot exceed the range -3.5V to 1V. Furthermore if the negative rail experiences a fault condition, such as overload or short circuit, the drain supply to the FETs will shut down avoiding excessive current flow.
The ZNBG3113/14 are available in QSOP20 for the minimum in device size. Device operating temperature is -40 to 70°C to suit a wide range of environmental conditions.
Part Number | ZNBG3113 |
LNA Bias Stages | 3 |
Mixer Bias Stages | |
Vout (V) | |
Max. Total Load (mA) | |
Vpol (V) | 14 to 15.5 |
FTone (kHz) | 22 |
LNA Vdrain (V) | 2.2 |
LNA Idrain (mA) | 0 to 15 |
Mixer Idrain (mA) | |
Vg off (V) | -2.5 |
Iq (mA) | 7 |
Vneg (V) | -3.0 |