Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
The VN771 is a device formed by three monolithic chips housed in a standard SO-28 package: a double high side and two Power MOSFETs. The double high side are made using STMicroelectronics VIPower technology; Power MOSFETs are made by using the new advanced strip lay-out technology This device is suitable to drive a DC motor in a bridge configuration as well as to be used as a quad switch for any low voltage application. The dual high side switches have built-in thermal shut-down to protect the chip from over temperature and short circuit,status output to provide indication for open load in off and on state, overtemperature conditions and stuck-on to VCC.
DUAL HIGH-SIDE SWITCH From the falling edge of the input signal, the status output, initially low to signal a fault condition (overtemperature or open load on-state), will go back to a high state with a different delay in case of overtemperature (tpovl) and in case of open open load (tpol) respectively.This feature allows to discriminate the nature of the detected fault. To protect the device against short circuit and over current condition, the thermal protection turns the integrated Power MOS off at a minimum junction temperature of 140 oC. When this temperature returns to 125 oC the switch is automatically turned on again. In short circuit the protection reacts with virtually no delay, the sensor (one for each channel) being located inside each of the two Power MOS areas. This positioning allows the device to operate with one channel in automatic thermal cycling and the other one on a normal load. An internal function of the devices ensures the fast demagnetization of inductive loads with a typical voltage (Vdemag) of -18V. This function allows to greatly reduces the power dissipation according to the formula:Pdem =0.5• Lload • (Iload)2 • [(VCC+Vdemag)/Vdemag] • f where f = switching frequency and Vdemag = demagnetization voltage.In this device if the GND pin is disconnected,with VCC not exceeding 16V, both channel will switch off.
Power MOSFETs During normal operation, the Input pin is electrically connected to the gate of the internal power MOSFET. The devices can be used as a switch from DC to very high frequency.
VN771 Maximum Ratings
Symbol
Parameter
Value
Unit
V(BR)DSS
Drain-Source Brekdown Voltage
40
V
IOUT
Output Current (continuous)
14
A
IR
Reverse Output Current
-14
A
IIN
Input Current
±10
mA
-VCC
Reverse Supply Current
-4
V
ISTAT
Status Current
±10
mA
VESD
Electrostatic Discharge (C=100pF,R=1.5K; )
2000
V
Ptot
Power Dissipation@ TC=25°C
Internally Limited
W
Tj
Junction operating temperature
-40 to 150
Tstg
Storage Temperature
-55 to 150
VN771 Connection Diagram
VN771K Parameters
Technical/Catalog Information
VN771K
Vendor
STMicroelectronics
Category
Integrated Circuits (ICs)
Package / Case
28-SOIC (7.5mm Width)
Mounting Type
Surface Mount
Type
H Bridge
Voltage - Supply
5.5 V ~ 36 V
On-State Resistance
60 mOhm
Current - Output / Channel
9A
Current - Peak Output
-
Packaging
Tube
Input Type
Non-Inverting
Number of Outputs
4
Operating Temperature
-40°C ~ 150°C
Drawing Number
*
Lead Free Status
Lead Free
RoHS Status
RoHS Compliant
Other Names
VN771K VN771K
VN771K General Description
The VN771K is a device formed by three monolithic chips housed in a standard SO-28 package: a double high side and two low side switches. Both the double high side and low side switches are made using |STMicroelectronics VIPower™ M0-3 Technology. This device is suitable to drive a DC motor in a bridge configuration as well as to be used as a quad switch for any low voltage application. The dual high side switches have built-in thermal shutdown to protect the chips from overtemperature and current limiter blocks to protect the device from short circuit. Status output is provided to indicate open load in off and on state and overtemperature. The low side switches are two OMNIFET II types (fully autoprotected Power MOSFET in VIPower™ technology). They have built-in thermal shutdown, linear current limitation and overvoltage clamping. Fault feedback for thermal intervention can be detected by monitoring the voltage at the input pin.
VN771K Maximum Ratings
Symbol
Parameter
Value
Unit
VCC
DC Supply Voltage
41
V
- VCC
Reverse DC Supply Voltage
-0.3
V
- IGND
DC Reverse Ground Pin Current
-200
mA
IOUT
DC Output Current
Internally Limited
A
- IOUT
Reverse DC Output Current
-6
A
IIN
DC Input Current
+/- 10
mA
ISTAT
DC Status Current
+/- 10
mA
VESD
Electrostatic Discharge (Human Body Model: R=1.5KW; C=100pF) - INPUT - STATUS - OUTPUT - VCC
4000 4000 5000 5000
V V V V
Ptot
Power Dissipation Tc=25°C
6
W
Tj
Junction Operating Temperature
Internally Limited
°C
Tc
Case Operating Temperature
- 40 to 150
°C
Tstg
Storage Temperature
- 55 to 150
°C
VN771K Features
· SUITED AS LOW VOLTAGE BRIDGE · LINEAR CURRENT LIMITATION · VERY LOW STAND-BY POWER DISSIPATION · SHORT CIRCUIT PROTECTED · STATUS FLAG DIAGNOSTIC (OPEN DRAIN) · INTEGRATED CLAMPING CIRCUITS · UNDERVOLTAGE PROTECTION · ESD PROTECTION