Published:2011/5/16 4:19:00 Author:Christina | Keyword: Op-amp, parallel
The Op-amp parallel circuit is as shown:
(View)
View full Circuit Diagram | Comments | Reading(1379)
Published:2011/5/16 3:33:00 Author:Christina | Keyword: 4-channel, keyboard, control circuit
View full Circuit Diagram | Comments | Reading(662)
Published:2011/5/16 3:29:00 Author:Christina | Keyword: Low-pass, filter
The Low-pass filter circuit is as shown:
(View)
View full Circuit Diagram | Comments | Reading(729)
Published:2011/5/13 1:11:00 Author:Nicole | Keyword: IGBT drive, 555 timer
View full Circuit Diagram | Comments | Reading(3601)
Published:2011/5/13 2:59:00 Author:Rebekka | Keyword: Automatic adjustment type, controller
The temperature controller can automatically adjust the electric heater input power while it is using light-emitting diode to display the temperature range. It keeps the controlled heater work at a constant temperature working condition. (View)
View full Circuit Diagram | Comments | Reading(655)
Published:2011/5/12 20:52:00 Author:Rebekka | Keyword: Thermal protection system
Thermal protection system circuit composed of MIC2951 is shown as above. The temperature threshold of the circuit is set by the adjustment of R2. (View)
View full Circuit Diagram | Comments | Reading(595)
Published:2011/5/15 5:46:00 Author:Michel | Keyword: Humidity Sensor, Interface Circuit
View full Circuit Diagram | Comments | Reading(643)
Published:2011/5/15 5:10:00 Author:John | Keyword: switch
IX0689 switch power supply circuit is given in the following.
(View)
View full Circuit Diagram | Comments | Reading(522)
Published:2011/5/15 3:37:00 Author:John | Keyword: High-speed voltage follower
The figure is a high-speed voltage follower circuit. The circuit is constituted by the VT3 and VT4. Al is the voltage follower circuit, which is constituted by the pin 7 of A1 and pin 4 of VT2 and VT6. Pin 7 of and pin 4 are just level shifting positions of the input signal voltage. Therefore, when the input signal is large, the power supply voltage on all-aspect of A1 and output end remains constant about 5V. As signal current through phase compensation capacitor from the Al-chip surges, the conversion rate has been greatly improved and high frequency distortion has been significantly reduced.
(View)
View full Circuit Diagram | Comments | Reading(1054)
Published:2011/5/16 3:19:00 Author:Rebekka | Keyword: over voltage detection , time delay protection
For some electrical equipments, the operating supply voltage range is strictly limited. Over-voltage or under-voltage will affect the work or even damage the equipment. The following shows a over-voltage and under voltage detection and time delay protection circuits. It can cut off the power supply when it is over-voltage or under-voltage. And it can start automatically after a period of delay. It is composed of two four-two input NAND gates CD4011. The over voltage and under-voltage detection circuit is composed of D1-D3 and RPl, RP2. D4 is trigger circuit. The relay driver circuit is composed of D7, D8 and transistor VT. The time relay restart circuit is composed of D5, D6 and R4, C5. (View)
View full Circuit Diagram | Comments | Reading(1582)
Published:2011/5/15 2:02:00 Author:John | Keyword: low-noise compensation circuit, bridge amplifier
bridge amplifier circuit with a low-noise compensation circuit
(View)
View full Circuit Diagram | Comments | Reading(972)
Published:2011/5/15 5:55:00 Author:Rebekka | Keyword: Home appliances , overvoltage protector
When the voltage suddenly rises because of some reason,household appliances such as the running refrigerators, washing machines, televisions, stereos, computers will face varying degrees of damage, even catch serious fire, causing great economic loss. This paper describes a simple over-voltage protection device, which provides protective effects on the appliance. When the voltage exceeds the allowable range, thepower supply will automatically cut off. Once the voltage turns to normal, the power can be automatically switched back. (View)
View full Circuit Diagram | Comments | Reading(1919)
Published:2011/5/15 2:59:00 Author:John | Keyword: AC amplifier
Non-inverting AC amplifier circuitis shown below.
(View)
View full Circuit Diagram | Comments | Reading(3127)
Published:2011/5/15 2:38:00 Author:John | Keyword: inverting amplifier
Inverting amplifier with high input impedance circuit is shown below.
(View)
View full Circuit Diagram | Comments | Reading(1911)
Published:2011/5/15 2:40:00 Author:John
Reset circuit is shown below.
(View)
View full Circuit Diagram | Comments | Reading(838)
Published:2011/5/15 2:54:00 Author:John | Keyword: A3 switch
A3 switch power supply circuit is shown below.
(View)
View full Circuit Diagram | Comments | Reading(630)
Published:2011/5/14 4:13:00 Author:Sue | Keyword: Frost, Alarm
Working Principle:
As seen in the figure 4-110, the frost alarm circuit consists of power circuit, temperature detection controlled circuit and alarm circuit.
When S is connected, the alarm circuit prepares to work. When the temperature is higher than 1℃, Q is disconnected and the alarm circuit doesn't work, and BL makes no sound. When the temperature is lower than1℃, Q is connected and IC begins to work. IC's 3 pin will output audio electric signal, which will promote BL to make a warning sound after the signal is amplified by V. (View)
View full Circuit Diagram | Comments | Reading(674)
Published:2011/5/13 3:28:00 Author:Ecco | Keyword: Automatic amplitude , control circuit, optical isolation
The circuit has a long time frequency stability, temperature changes can be ignored, and it eliminates the pulse load on the frequency, the oscillator uses emitter coupled circuit and 2N3707 low-noise transistor. In addition, it is also given the output amplifier and automatic amplitude control circuit. This circuit is designed for ham using radio equipment.
(View)
View full Circuit Diagram | Comments | Reading(872)
Published:2011/5/15 5:14:00 Author:Rebekka | Keyword: SBC overvoltage protection
The circuit is shown as above. It can use +5 V operating voltage SBC power supply. It can prevent the damage of the SBC to +5 V the entire SBC because of overvoltage. (View)
View full Circuit Diagram | Comments | Reading(671)
Published:2011/5/13 1:31:00 Author:Ecco | Keyword: Optically , isolated , input , protection
Diodes and transistors form the circuit, when the input voltage range is 3 ~ 30V DC, the input current of MOC3011 optical isolator LED is limited to be less than the safety limit of 15mA. In the case of reverse polarity accident, the circuit can protect the light-emitting diodes.
(View)
View full Circuit Diagram | Comments | Reading(1079)
Pages:266/312 At 20261262263264265266267268269270271272273274275276277278279280Under 20 |