Index 49

Position: Home > Circuit Diagram > Basic Circuit > >Index 49

Low Cost Custom Prototype PCB Manufacturer

TOUCH SWITCH and TOUCH ON-OFF Circuit

Published:2013/3/5 20:55:00 Author:Ecco | Keyword: TOUCH SWITCH , TOUCH ON-OFF

TOUCH SWITCH and TOUCH ON-OFF Circuit
The Touch Switch circuit will detect stray voltages produced by mains voltages and electrostatic build-up in a room. In the first circuit, pin 2 must see a LOW for the circuit to activate. If sufficient static voltage is detected by the plate, the chip will change state. If not, you will need to touch the plate and the 0v rail. In the second circuit, two touch plates are provided and the resistance of your finger changes the voltage on pin 2 or 6 to toggle the 555. (View)

View full Circuit Diagram | Comments | Reading(6488)

TILT SWITCH Circuit

Published:2013/3/5 20:53:00 Author:Ecco | Keyword: TILT SWITCH

TILT SWITCH Circuit
The output is LOW at start-up due to the capacitor on pin 4. When the mercury switch closes, the output goes HIGH and remains HIGH until the reset button is pressed. This circuit is called a LATCH. (View)

View full Circuit Diagram | Comments | Reading(934)

STUN GUN Circuit

Published:2013/3/5 20:52:00 Author:Ecco | Keyword: STUN GUN

STUN GUN Circuit
This circuit produces a very high voltage and care must be used to prevent getting a nasty shock.The transformer can produce over 1,000v and the 8-stage multiplier can produce up to 20,000v. (View)

View full Circuit Diagram | Comments | Reading(4601)

SIREN 100dB Circuit

Published:2013/3/5 20:46:00 Author:Ecco | Keyword: SIREN 100dB

SIREN 100dB Circuit
This is a very loud siren and if two or more piezo's are located in a room, the burglar does not know where the sound is coming from. A robber will not stay anywhere with an ear-piercing sound as he cannot hear if someone is approaching. It's the best deterrent you can get. The F contact on the piezo is feedback and is not needed in this circuit. (View)

View full Circuit Diagram | Comments | Reading(1193)

POLICE SIREN Circuit

Published:2013/3/5 20:37:00 Author:Ecco | Keyword: POLICE SIREN

The Police Siren circuit uses two 555's to produce an up-down wailing sound. The first 555 is wired as a low-frequency oscillator to control the VOLTAGE CONTROL pin 5 of the second 555. The voltage shift on pin 5 causes the frequency of the second oscillator to rise and fall. (View)

View full Circuit Diagram | Comments | Reading(986)

MUSIC BOX Circuit

Published:2013/3/5 0:33:00 Author:Ecco | Keyword: MUSIC BOX

MUSIC BOX Circuit
This circuit produces 10 different tones and by selecting suitable values to change the voltage on pin 5, the result can be quite pleasing. Note: the two unused outputs of the 4017 produce a tone equal to that produced by the 555 when pin 5 has no external control voltage. (View)

View full Circuit Diagram | Comments | Reading(1538)

MOTOR PWM Circuit

Published:2013/3/5 0:32:00 Author:Ecco | Keyword: MOTOR PWM

MOTOR PWM Circuit
The speed of a motor can be adjusted by this circuit, from 5% to 95%. (View)

View full Circuit Diagram | Comments | Reading(930)

MOSQUITO REPELLER Circuit

Published:2013/3/5 0:31:00 Author:Ecco | Keyword: MOSQUITO REPELLER

MOSQUITO REPELLER Circuit
This circuit produces a tone above the human audible range and this is supposed to keep the mosquitoes away. You need a piezo diaphragm that will respond to 15kHz and these are very difficult to find. (View)

View full Circuit Diagram | Comments | Reading(2839)

MODEL RAILWAY TIME Circuit

Published:2013/3/5 0:30:00 Author:Ecco | Keyword: MODEL RAILWAY, TIME Circuit

MODEL RAILWAY TIME Circuit
Here is a circuit that will convert any clock mechanism into Model Railway Time. For those who enjoy model railways, the ultimate is to have a fast clock to match the scale of the layout. This circuit will appear to make time fly by turning the seconds hand once every 6 seconds. The timing can be adjusted by changing the 47k. The electronics in the clock is disconnected from the coil and the circuit drives the coil directly. The circuit takes a lot more current than the original clock (1,000 times more) but this is one way to do the job without a sophisticated chip. (View)

View full Circuit Diagram | Comments | Reading(930)

LATCH Circuit

Published:2013/3/5 0:23:00 Author:Ecco | Keyword: LATCH

LATCH Circuit
This circuit is a LATCH and remains ACTIVE when the push-button has been pressed for an INSTANT and released. (View)

View full Circuit Diagram | Comments | Reading(1641)

LASER RAY Circuit

Published:2013/3/5 0:22:00 Author:Ecco | Keyword: LASER RAY

LASER RAY Circuit
This circuit produces a weird Laser Ray sound and flashes a white LED at approx 5Hz: (View)

View full Circuit Diagram | Comments | Reading(1045)

KNIGHT RIDER Circuit

Published:2013/3/5 0:21:00 Author:Ecco | Keyword: KNIGHT RIDER

This circuit mimics the lights in knight rider's car. They flash one at a time chasing each other. Overview In the Knight Rider circuit, the 555 is wired as an oscillator (Astable mode). The output of the 555 is directly connected to the input of a 4017 decade counter. The input of the 4017 counter is called the CLOCK line. The 10 outputs Q0 to Q9 become active, one at a time, on the rising edge of the waveform from the 555. Each output can deliver about 20mA but a LED should not be connected to the output without a current-limiting resistor (100R or 220R). Using six 3mm LEDs, the display can be placed in the front of a model car to give a very realistic effect. The same outputs can be taken to driver transistors to produce a larger version of the display. (View)

View full Circuit Diagram | Comments | Reading(2445)

HEE HAW SIREN Circuit

Published:2013/3/5 0:20:00 Author:Ecco | Keyword: HEE HAW SIREN

HEE HAW SIREN Circuit
Build the circuit and listen. Change the resistors and capacitors to get all sorts of different results. (View)

View full Circuit Diagram | Comments | Reading(904)

DRIVING A RELAY Circuit

Published:2013/3/4 21:44:00 Author:Ecco | Keyword: DRIVING A RELAY

DRIVING A RELAY Circuit
The 555 will activate a relay. When pins 2 and 6 are connected as an input, the chip requires only about 1uA to activate the output. This is equivalent to a gain of about 200,000,000 (200 million) and represents about 4 stages of amplification via transistors.In the first circuit,the output will be opposite to the input. The relay can be connected high or low as show in the second diagram. One point to note: The input must be higher than 2/3V for the output to be low and below 1/3V for the output to be high. This is called HYSTERESIS and prevents any noise on the input creating relay chatter. (View)

View full Circuit Diagram | Comments | Reading(1090)

Hulda Clark's Zapper Circuit

Published:2013/3/4 21:34:00 Author:Ecco | Keyword: Hulda Clark's Zapper

Hulda Clark's Zapper Circuit

This is the circuit for Dr. Hulda Clark's Zapper, designed in 2003. The frequency is approximately 30kHz positive offset square wave. It has a red LED light that lights up when the unit is on. Perfect for regular zapping, extended zapping and other Hulda Clark related experiments. This device is used tocure, treat and prevent any disease. It will cure anything. Simply hold the two probes (one in each hand) for 5-10 minutes then rest for 20 minutes, then repeat two more times. Do this each day and you will be cured. On the other side of the coin is the claim that Dr Hulda Clark is a complete quack. Here is a website called: Quackwatch. The second diagram shows the two copper tubes and the circuit in a plastic box. I am still at a loss to see how any energy can transfer from this quack machine, through the skin (50k skin resistance and 9v supply) and zap a bug in your intestine. It's a bit like saying I will kill all the mice in a haystack by stabbing the stack with a needle. (View)

View full Circuit Diagram | Comments | Reading(0)

2nd Order Opamp Filters

Published:2013/3/4 20:59:00 Author:Ecco | Keyword: 2nd Order , Opamp , Filters

2nd Order Opamp Filters
The figures below illustrate using opamps as active 2nd order filters. Three 2nd order filters are shown, low pass, high pass, and bandpass. Each of these filters will attenuate frequencies outside their passband at a rate of 12dB per octave or 1/4 the voltage amplitude for each octave of frequency increase or decrease outside the passband. First order low or high pass cutoff frequency (-3dB point) = 1/(2pi*R*C) 2nd order low or high pass cutoff frequency (-3dB point) = 1/2pi(R1*R2*C1*C2)^.5 Example for 200 Hz cutoff frequency - R1=R2=7.95K, C1=C2=0.1uF (View)