TB62200F-EL, TB62201AFG, TB62201F Selling Leads, Datasheet
MFG:66 Package Cooled:SOPH D/C:98
TB62200F-EL, TB62201AFG, TB62201F Datasheet download
Part Number: TB62200F-EL
MFG: 66
Package Cooled: SOPH
D/C: 98
MFG:66 Package Cooled:SOPH D/C:98
TB62200F-EL, TB62201AFG, TB62201F Datasheet download
MFG: 66
Package Cooled: SOPH
D/C: 98
Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
TOP
PDF/DataSheet Download
Datasheet: TB6066FNG
File Size: 247874 KB
Manufacturer: TOSHIBA [Toshiba Semiconductor]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: TB6066FNG
File Size: 247874 KB
Manufacturer: TOSHIBA [Toshiba Semiconductor]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: TB6066FNG
File Size: 247874 KB
Manufacturer: TOSHIBA [Toshiba Semiconductor]
Download : Click here to Download
The TB62201AFG is a dual-stepping motor driver driven by chopper micro-step pseudo sine wave.
To drive two-phase stepping motors, Two pairs of 16-bit latch and shift registers are built in the IC. The IC is optimal for driving stepping motors at high efficiency and with low-torque ripple.
The IC supports Mixed Decay mode for switching the attenuation ratio at chopping. The switching time for the attenuation ratio can be switched in four stages according to the load.
Characteristics | Symbol | Rating | Unit |
Logic supply voltage | VDD | 7 | V |
Output voltage | VM | 40 | V |
Output current | IOUT | 1.5 | A/phase |
Current detect pin voltage | VRS | VM ± 4.5 | V |
Charge pump pin maximum voltage (CCP1 pin) |
VH | VM + 7.0 | V |
Logic input voltage | VIN | to VDD + 0.4 | V |
Power dissipation | PD | 1.4 | W |
3.2 | W | ||
Operating temperature | Topr | −40 to 85 | |
Storage temperature | Tstg | −50 to 150 | |
Junction temperature | Tj | 150 |
Note 1: Perform thermal calculations for the maximum current value under normal conditions. Use the IC at 1.2 A or less per phase.
Note 2: Input 7 V or less as VIN.
Note 3: Measured for the IC only. (Ta = 25°C)
Note 4: Measured when mounted on the board. (Ta = 25°C)
Ta: IC ambient temperature
Topr: IC ambient temperature when starting operation
Tj: IC chip temperature during operation Tj (max) is controlled by TSD (thermal shut down circuit)
` Two stepping motors driven by micro-step pseudo sine wave are controlled by a single driver IC
` Monolithic Bi-CMOS IC
` Low ON-resistance of Ron = 0.5 (Tj = 25°C @ 1.0 A: typ.)
` ESD protection Exceeds 2000 V, MIL-STD-883D
` Two pairs of built-in 16-bit shift and latch registers
` Two pairs of built-in 4-bit DA converters for micro steps
` Built-in ISD, TSD, VDD&VM power monitor (reset) circuit for protection
` Built-in charge pump circuit (two external capacitors)
` 36-pin power flat package (HSOP36-P-450-0.65)
` Output voltage: 40 V max
` Output current: 1.5 A/phase max
` Built-in Mixed Decay mode enables specification of four-stage attenuation ratio. (The attenuation ratio table can be overwritten externally.)
` Chopping frequency can be set by external resistors and capacitors. High-speed chopping possible at 100 kHz or higher.
Note: When using the IC, pay attention to thermal conditions.
These devices are easy damage by high static voltage.
In regards to this, please handle with care.