TB62202AFG

Features: `Two stepping motors driven by micro−step pseudo sine wave are controlled by a single driver IC`Monolithic Bi-CMOS IC`Low ON-resistance of Ron = 1.2 (Tj = 25 @1.0 A: Typ.)`Two pairs of built-in 16-bit shift and latch registers`Two pairs of built-in 4-bit DA converters for micro st...

product image

TB62202AFG Picture
SeekIC No. : 004512665 Detail

TB62202AFG: Features: `Two stepping motors driven by micro−step pseudo sine wave are controlled by a single driver IC`Monolithic Bi-CMOS IC`Low ON-resistance of Ron = 1.2 (Tj = 25 @1.0 A: Typ.)`Two pairs...

floor Price/Ceiling Price

Part Number:
TB62202AFG
Supply Ability:
5000

Price Break

  • Qty
  • 1~5000
  • Unit Price
  • Negotiable
  • Processing time
  • 15 Days
Total Cost: $ 0.00

SeekIC Buyer Protection PLUS - newly updated for 2013!

  • Escrow Protection.
  • Guaranteed refunds.
  • Secure payments.
  • Learn more >>

Month Sales

268 Transactions

Rating

evaluate  (4.8 stars)

Upload time: 2024/11/22

Payment Methods

All payment methods are secure and covered by SeekIC Buyer Protection PLUS.

Notice: When you place an order, your payment is made to SeekIC and not to your seller. SeekIC only pays the seller after confirming you have received your order. We will also never share your payment details with your seller.
Product Details

Description



Features:

`Two stepping motors driven by micro−step pseudo sine wave are controlled by a single driver IC
`Monolithic Bi-CMOS IC
`Low ON-resistance of Ron = 1.2 (Tj = 25 @1.0 A: Typ.)
`Two pairs of built-in 16-bit shift and latch registers
`Two pairs of built-in 4-bit DA converters for micro steps
`Built-in ISD, TSD, VDD and VM power monitor (reset) circuit for protection
`Built-in charge pump circuit (two external capacitors)
`36-pin power flat package (HSOP36-P-450-0.65)
`Output voltage: 40 V max
`Output current: 1.0 A/phase max
`Built-in Mixed Decay mode enables specification of four-stage attenuation ratio.
(The attenuation ratio table can be overwritten externally.)
`Chopping frequency can be set by external resistors and capacitors. High-speed chopping possible at 100 kHz or
higher.



Specifications

Characteristics Symbol Rating Unit
Logic supply voltage VDD 7 V
Output voltage VM 40 V
Output current IOUT 1.5 A/phase (Note 1)
Current detect pin voltage VRS VM ± 4.5 V
Charge pump pin maximum voltage (CCP1 pin) VH VM ± 7.0 V
Logic input voltage VIN to VDD + 0.4 V
Power dissipation PD 1.4 W (Note 2)
3.2 W (Note 3)
Operating temperature Topr −40 to 85
Storage temperature Tstg −50 to 150
Junction temperature Tj 150

Note 1: Perform thermal calculations for the maximum current value under normal conditions. Use the IC at 1.2 A or
less per phase.
Note 2: Input 7 V or less as VIN.
Note 3: Measured for the IC only. (Ta = 25)
Note 4: Measured when mounted on the board. (Ta = 25)
            Ta: IC ambient temperature
            Topr: IC ambient temperature when starting operation
            Tj: IC chip temperature during operation Tj (max) is controlled by TSD (thermal shut down circuit)



Description

The TB62202AFG is a dual-stepping motor driver driven by chopper micro-step pseudo sine wave.

To drive two-phase stepping motors, Two pairs of 16-bit latch and shift registers are built in the IC. The IC is optimal for driving stepping motors at high efficiency and with low-torque ripple.

The IC supports Mixed Decay mode for switching the attenuation ratio at chopping. The switching time for the attenuation ratio can be switched in four stages according to the load.




Customers Who Bought This Item Also Bought

Margin,quality,low-cost products with low minimum orders. Secure your online payments with SeekIC Buyer Protection.
Soldering, Desoldering, Rework Products
Motors, Solenoids, Driver Boards/Modules
RF and RFID
Programmers, Development Systems
Inductors, Coils, Chokes
Circuit Protection
View more