Features: Power supply voltage of 2.7 to 3.1 voltHigh performance -55 ns - 65 ns (65 ns Flash, 70ns pSRAM)Packages - 7 x 9 x 1.2mm 56 ball FBGA - 8 x 11.6 x 1.2mm 64 ball FBGA - 8 x 11.6 x 1.4mm 84 ball FBGAOperating Temperature - 25°C to +85°C - 40°C to +85°CSpecificationsStorage Temperature Pla...
S71PL2540J: Features: Power supply voltage of 2.7 to 3.1 voltHigh performance -55 ns - 65 ns (65 ns Flash, 70ns pSRAM)Packages - 7 x 9 x 1.2mm 56 ball FBGA - 8 x 11.6 x 1.2mm 64 ball FBGA - 8 x 11.6 x 1.4mm 84...
SeekIC Buyer Protection PLUS - newly updated for 2013!
268 Transactions
All payment methods are secure and covered by SeekIC Buyer Protection PLUS.
Storage Temperature Plastic Packages . . . . . . . . . . . . . 65°C to +150°C
Ambient Temperature with Power Applied . . . . . . . . . . . 65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to +4.0 V
RESET# (Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to +13.0 V
WP#/ACC (Note 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 V to +10.5 V
All other pins (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . .0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3). . . . . . . . . . . . . . . . . . . . . . . . 200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is 0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to 2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 8.
2. Minimum DC input voltage on pins A9, OE#, RESET#, and WP#/ACC is 0.5 V. During voltage transitions, A9, OE#, WP#/ACC, and RESET# may overshoot VSS to 2.0 V for periods of up to 20 ns. See Figure 8. Maximum DC input voltage on pin A9, OE#, and RESET# is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns. Maximum DC input voltage on WP#/ACC is +9.5 V which may overshoot to +12.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
4. Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied. Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
The S71PL2540J series is a product line of stacked Multi-Chip Product (MCP) packages and consists of:
One or more S29PL (Simultaneous Read/Write) Flash memory die
pSRAM or SRAM
The 256Mb Flash memory consists of two S29PL127J devices. In this case, CE#f2 is used to access the second Flash and no extra address lines are required.