Published:2011/5/13 5:08:00 Author:May | Keyword: digital, eight, D flip flop
74LS379, 74F379, 74S379, 74HC379 eight D flip flop74××175 is similar to this circuit. It only has one common allow end, and not common clear end.function table ( every flip flop)Q0=the level of Q before building stable state input condition
(View)
View full Circuit Diagram | Comments | Reading(1561)
Published:2011/5/13 5:08:00 Author:May | Keyword: digital, six D flip-flop
74LS378, 74F378, 74S378, 74HC378 six D trigger74××174 is similar to this circuit. It only has one public permitting but not public clearing end. (View)
View full Circuit Diagram | Comments | Reading(722)
Published:2011/5/13 5:06:00 Author:May | Keyword: digital, eight D flip-flop
Q0=the level of Q before building stability input condition.74LS377, 74F377, 74S377, 74HC377 eight D trigger74××273 is similar to this circuit. It only has one public permitting but not public clearing end. (View)
View full Circuit Diagram | Comments | Reading(748)
Published:2009/6/19 2:28:00 Author:May
View full Circuit Diagram | Comments | Reading(738)
Published:2011/5/13 5:02:00 Author:May | Keyword: digital, four J-K, non-flip-flop
74376 four J-K non-triggerfull buffer output: typical clock input frequency is 45MHz
(View)
View full Circuit Diagram | Comments | Reading(706)
Published:2009/6/19 2:27:00 Author:May
This filter is for CH3, in order to get a vestigial sideband TV signal. It is designed for 75-Ω im-pedance levels. (View)
View full Circuit Diagram | Comments | Reading(659)
Published:2011/5/11 3:57:00 Author:May | Keyword: digital, eight buffer, line driver, three-state
74S340, 74S341, 74S344 eight buffer/line driver (tristate)Their pin diagrams is seperately same as 74LS240, 74LS241, 74LS244.
(View)
View full Circuit Diagram | Comments | Reading(536)
Published:2009/6/19 2:26:00 Author:May
The voltage at Output A, which should be unloaded by a follower, responds as though ES were di-rected to the RC filter, but the filter's break frequency were proportional to Ec[i.e,.=Ec/(20πRC)] The frequency response has a break at f2; and the 6-dB/octave rolloff. The voltage at Output B has the same response, up to [f1 (f = 1/(20πRC)], then levels off at a constant attenuation of f2/f1 = Ec\10.For example, if R = 8kΩ, C = 0.002μF, Output A has a pole at 100 Hz to 10 kHz and can be loaded.The circuit can be converted to high-pass by interchanging C and R. (View)
View full Circuit Diagram | Comments | Reading(1)
Published:2011/5/11 3:58:00 Author:May | Keyword: digital, 4-bit, 2 selection 1, data selector, register output
View full Circuit Diagram | Comments | Reading(951)
Published:2011/5/11 3:59:00 Author:May | Keyword: digital, digital phase-locked loop
View full Circuit Diagram | Comments | Reading(931)
Published:2009/6/19 2:23:00 Author:May
When the light is off, it can be turned on with either switch. When it's on, it can be turned off with either switch. (View)
View full Circuit Diagram | Comments | Reading(655)
Published:2011/5/11 3:59:00 Author:May | Keyword: digital, eight bits, shift register, serial/serial/parallel out
View full Circuit Diagram | Comments | Reading(3006)
Published:2009/6/19 2:18:00 Author:May
A simple way to provide +9 V at 100 mA from a 12-V auto source. Applications include small radios, cassettes, etc. (View)
View full Circuit Diagram | Comments | Reading(708)
Published:2009/6/19 2:18:00 Author:May
View full Circuit Diagram | Comments | Reading(812)
Published:2009/6/19 2:17:00 Author:May
This figure shows a circuit where the Q can be varied from 0.3 to 50. A fraction of the output is fed back to R3 and C3 by a second voltage follower, and the notch Q is dependent on the amount of signal fed back. A second follower is necessary to drive the twin T from a low-resistance source so that the notch frequency and depth will not change with the potentiometer setting. (View)
View full Circuit Diagram | Comments | Reading(0)
Published:2009/6/19 2:16:00 Author:May
This shows a twin T network connected to an LM102 to form a high Q, 60-Hz notch filter. The Junction of R3 and C3: which is normally connected to ground, is bootstrapped to the output of the follower. Because the output of the follower is a very low impedance, neither the depth nor the frequency of the notch change; however, the Q is raised in proportion to the amount of signal fed back to R3 and C3. (View)
View full Circuit Diagram | Comments | Reading(0)
Published:2009/6/19 2:11:00 Author:May
In order to match two transistors, select Q1 and Q2 so that they give zero readings(or as close as possible)on a DVM. The DVM acts as a null detector. An analog meter can be substituted. S1 should be set for an appropriate level of base current(approximately 8,80,or 800 μA). (View)
View full Circuit Diagram | Comments | Reading(1327)
Published:2009/6/19 2:09:00 Author:May
In this high-performance reference circuit, U1 is a device from the REF190 series producing de-vice-selectable outputs of 2.5, 4.5, and 5 V with simple, noncritical external circuitry. An Analog Devices REF 19 X(see the table in the figure)is used to derive a reference voltage. (View)
View full Circuit Diagram | Comments | Reading(840)
Published:2009/6/19 2:09:00 Author:May
View full Circuit Diagram | Comments | Reading(551)
Published:2009/6/19 2:08:00 Author:May
This circuit uses only two capacitors.The amplifier on the right supplies a controlled amount of characteristics. Resistors R5 and R8 are used to bias the outvoltage of the amplifiers at V+/2. (View)
View full Circuit Diagram | Comments | Reading(1)
Pages:350/471 At 20341342343344345346347348349350351352353354355356357358359360Under 20 |