Published:2011/8/19 1:04:00 Author:Jessie | Keyword: Double op-amp realization
View full Circuit Diagram | Comments | Reading(741)
Published:2011/8/19 2:04:00 Author:Jessie | Keyword: Single op-amp realization
If it uses the band-pass filter composed of the components with parameters being very closed, it is prone to oscillation. The resistor connected to should be selected in E-96 1% series, or you will destroy the oscillation conditions. (View)
View full Circuit Diagram | Comments | Reading(658)
Published:2011/10/14 3:14:00 Author:Ecco | Keyword: video amplifier
View full Circuit Diagram | Comments | Reading(2937)
Published:2011/10/14 1:48:00 Author:Ecco | Keyword: self-bias , power amplifier , tube
The typical self-bias power amplifier stage circuit withoutdebugging of tube
The typical semi-debugself-bias power amplifier stage circuit of tube
(View)
View full Circuit Diagram | Comments | Reading(1233)
Published:2011/10/14 2:11:00 Author:Ecco | Keyword: video amplifier
View full Circuit Diagram | Comments | Reading(7326)
Published:2011/10/14 2:21:00 Author:Ecco | Keyword: short-wave signal amplifier
View full Circuit Diagram | Comments | Reading(943)
Published:2011/10/14 2:12:00 Author:Ecco | Keyword: Broadband short-wave amplification
View full Circuit Diagram | Comments | Reading(752)
Published:2011/10/14 2:13:00 Author:Ecco | Keyword: Short-wave signal amplifier
View full Circuit Diagram | Comments | Reading(1281)
Published:2011/10/16 22:33:00 Author:Ecco | Keyword: Low-noise amplifier
View full Circuit Diagram | Comments | Reading(2215)
Published:2011/10/17 1:13:00 Author:Ecco | Keyword: Differential amplifier
View full Circuit Diagram | Comments | Reading(747)
Published:2011/10/14 3:12:00 Author:Ecco | Keyword: Common video amplifier
View full Circuit Diagram | Comments | Reading(4697)
Published:2011/10/14 2:24:00 Author:Ecco | Keyword: video amplifier
View full Circuit Diagram | Comments | Reading(1917)
Published:2011/9/15 1:38:00 Author:Rebekka | Keyword: JFET gate grounding preamplifier
Figure 1-1 is the example of joint types FET 2SK125(SONY) grounded gate amplifier. So when you use the gate grounding circuit, you could separate the input and output by using the grounding gate electrode on printing copper foil. The power gain of the circuit is about 10~12dB, NF is about 2dB. The LC value in the circuit change with frequency. You should choose table 1-1, and L1, L2 are at toroidal core amine line of poly resin. The diameter is about 0.3mm. It should insert in the substrate directly to avoid producing stray capacitance. You could Adding a source of resistor where you want to adjust and keep the drain current being about 10mA. In addition, adjusting trimmer condenser can get the highest sensitivity. (View)
View full Circuit Diagram | Comments | Reading(3095)
Published:2011/9/15 1:35:00 Author:Rebekka | Keyword: broadband power amplifier
The picture shows the 1W wide-broadband power amplifier with frequency in 1 ~ 50MHz and using 2SC1970; Input and output coils use broadband transformer composed of toroidal winding for impedance conversion. 2SC1970 is the 170MHz power transistor, so it can be used for the VHF band broadband amplifier. In the circuit , the coupling capacitor (CoupIingCapacitor) and Bypass Capacitor are connected with 2 to 3 0.01μF ceramic capacitor in parallel, the most important thingis to reduce the impedance (Impedance), at the same time, the current flows the channel is also wider. (View)
View full Circuit Diagram | Comments | Reading(2717)
Published:2011/9/14 21:41:00 Author:Rebekka | Keyword: broadband amplifier circuit
μPC1651G(Japanese electrical apparatus) series use high-frequency broadband amplifier. Micro-disc shape(Micro Disk Type). Frequency coverage is 10M~1200MHz(@-3dB), and the gain is 19dB(@f=500MHz). NF is about 5dB, so it's not good to use receiver preamplifier. But there is not much effect on using receiver preamplifier and IF amplifying circuit. Figure 1 is broadband preamplifier composed of μPC1651G. Although it has a simple structure, you should pay attention to the effect of lead inductance when youwant to get1200MHz, so it is better to use short wiring. The circuit cases use broadband amplifier composed of glass epoxy double-sided substrate. The bypass capasitor of power terminal should be connected between IC power supply and ground. It should be near to IC.
(View)
View full Circuit Diagram | Comments | Reading(1497)
Published:2011/9/26 21:21:00 Author:Rebekka | Keyword: Operational amplifier , zero setting method
The figure shows a simple common zero seting circuit. Its integrated chip can be used for the OPA37, LH0044B and so on. As the adjustment of the network (R1, R2 and R3 form a potentiometer) uses the 15V positive and negative power supply, almost any amplifier is suitablefor zero seting. ①, ⑧ pins are zero ends. The resistors R1 and R2 are high-value resistors. It is usually taken to be 5MΩ for the LH0044B. It only has a few microamps of current and plus an adjustable voltage on R2, so that the two currents are imbalance and adjust the offset voltage. (View)
View full Circuit Diagram | Comments | Reading(754)
Published:2011/8/3 2:33:00 Author:Ecco | Keyword: Microphone amplifier
View full Circuit Diagram | Comments | Reading(777)
Published:2011/9/19 1:16:00 Author:Ecco | Keyword: In-phase , composite DC amplifier
It uses the four operational amplifier 774 to achieve its parallel work, andit can drive 500Ω loads with goodlinear in the ± 10V range.
(View)
View full Circuit Diagram | Comments | Reading(840)
Published:2011/9/25 22:11:00 Author:Ecco | Keyword: Power amplifier , Marantz, electronic valve
Whole frequency response rangeis relatively flat from 10Hz to 40Hz.
(View)
View full Circuit Diagram | Comments | Reading(1319)
Published:2011/9/25 22:17:00 Author:Ecco | Keyword: Tube SRPP inverter
SRPP tube common-cathode inverter circuit:
Tube SRPP common-gateinvertercircuit:
(View)
View full Circuit Diagram | Comments | Reading(2439)
Pages:55/250 At 204142434445464748495051525354555657585960Under 20 |