NE1617DS-T, NE1618, NE16189X136 Selling Leads, Datasheet
MFG:PHILIPS Package Cooled:07+ D/C:SSOP
NE1617DS-T, NE1618, NE16189X136 Datasheet download
Part Number: NE1617DS-T
MFG: PHILIPS
Package Cooled: 07+
D/C: SSOP
MFG:PHILIPS Package Cooled:07+ D/C:SSOP
NE1617DS-T, NE1618, NE16189X136 Datasheet download
MFG: PHILIPS
Package Cooled: 07+
D/C: SSOP
Want to post a buying lead? If you are not a member yet, please select the specific/related part number first and then fill the quantity and your contact details in the "Request for Quotation Form" on the left, and then click "Send RFQ".Your buying lead can then be posted, and the reliable suppliers will quote via our online message system or other channels soon.
TOP
PDF/DataSheet Download
Datasheet: NE1617
File Size: 165984 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: NE1618
File Size: 144692 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
PDF/DataSheet Download
Datasheet: NE1617
File Size: 165984 KB
Manufacturer: PHILIPS [Philips Semiconductors]
Download : Click here to Download
The NE1618 is an accurate two-channel temperature monitor. It measures the temperature of itself and the temperature of a remote sensor. It can replace the NE1617 for a more precise measurement to the remote temperature when it operates in extended mode. The remote sensor is a diode connected transistor being in the form of either a discrete NPN/PNP, such as the 2N3904/2N3906, or a diode connected PNP built into another die, such as is done on some INTEL microprocessors.
The temperature of both the remote and local sensors are stored in the registers that can be read via a 2-wire SMBus. The data in the temp reading registers are updated at the end of every data conversion when the conversion is enable. At all time, data conversion is initiated automatically in the rate defined by the programmable data in the conversion rate register. However, a conversion can be forced to occur immediately by a one-shot programming.
The local temp is always measured with a resolution of 1.0 C but the remote temp can be measured in either one of two modes: extended mode with a resolution of 0.125 and basic mode with a resolution of 1.0 . The mode is set up automatically according to the programmable data stored in the conversion rate register. (See Table 6). Extended mode is set when the conversion rate is slow (rate 0.7 Hz or less) and normal mode is set when the rate is high (conversion rate of 2, 4, or 8 Hz).
There is also an alarm that senses either an over or under temperature condition. The trip points for this alarm are alsoprogrammable. The device can have 1 of 9 addresses (determined by 2 address pins), so there can be up to 9 of the NE1618 on the SMBus. It can also be put in a standby mode (in order to save power). This can be done either with software (over the SMBus) or pin). with hardware (using the STBY pin)
PARAMETER | MIN. | MAX. | UNIT |
VDD to GND | -0.3 | +6 | V |
D+, ADD0, ADD1 | -0.3 | VDD +0.3 | V |
D-C to GN | -0.3 | +0.8 | V |
SCLK, SDATA, ALERT, STBY | -0.3 | +6 | V |
Input current SDATA | -1 | +50 | mA |
D-C curren | ±1 | mA | |
ESD Human Body Model Machine Model |
- - |
2000 200 |
V V |
Operating temperature range | 0 | +120 | |
Maximum junction temperature | +150 | ||
Storage temperature range | -65 | +150 |
NOTE:
1.This is a stress rating only. Functional operation of the device as indicated in the operational section is not applied to this absolute maximum rating. Stress above those listed in !Absolute maximum ratings! may cause permanent damage to the device, and exposure to anyf these rating conditions for extended periods may affect device reliability.