USB3318

Features:

`USB-IF "Hi-Speed" compliant to the Universal Serial Bus Specification Rev 2.0
`Interface compliant with the ULPI Specification revision 1.1 as a Single Data Rate (SDR) PHY
`1.8V to 3.3V IO Voltage (+/- 10%)
`SMSC flexPWRTM Technology
- Low current design ideal for battery powered applications
- "Sleep" mode tri-states all ULPI pins and places the part in a low current state
`Supports FS pre-amble for FS hubs with a LS device attached (UTMI+ Level 3)
`Supports HS SOF and LS keep-alive pulse
`Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.0a specification
`Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
`Allows host to turn VBUS off to conserve battery power in OTG applications
`Support OTG monitoring of VBUS levels with internal comparators
`"Wrapper-less" design for optimal timing performance and design ease
- Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI bridge
`Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground
`13MHz Reference Clock operation
- 0 to 3.6V input drive tolerant
- Able to accept "noisy" clock sources
`Internal low jitter PLL for 480MHz Hi-Speed USB operation
`Internal detection of the value of resistance to ground on the ID pin
`Integrated battery to 3.3V LDO regulator
- 2.2uF bypass capacitor
- 100mV dropout voltage
`Integrated ESD protection circuits
- Up to +-15kV without any external devices
`Carkit UART mode for non-USB serial data transfers
`Industrial Operating Temperature -40°C to +85°C
`Packaging Options
- 24 pin QFN lead-free RoHS compliant package (4 x 4 x 0.90 mm height)



`USB-IF "Hi-Speed" compliant to the Universal Serial Bus Specification Rev 2.0
`Interface compliant with the ULPI Specification revision 1.1 as a Single Data Rate (SDR) PHY
`1.8V to 3.3V IO Voltage (+/- 10%)
`SMSC flexPWRTM Technology
- Low current design ideal for battery powered applications
- "Sleep" mode tri-states all ULPI pins and places the part in a low current state
`Supports FS pre-amble for FS hubs with a LS device attached (UTMI+ Level 3)
`Supports HS SOF and LS keep-alive pulse
`Includes full support for the optional On-The-Go (OTG) protocol detailed in the On-The-Go Supplement Revision 1.0a specification
`Supports the OTG Host Negotiation Protocol (HNP) and Session Request Protocol (SRP)
`Allows host to turn VBUS off to conserve battery power in OTG applications
`Support OTG monitoring of VBUS levels with internal comparators
`"Wrapper-less" design for optimal timing performance and design ease
- Low Latency Hi-Speed Receiver (43 Hi-Speed clocks Max) allows use of legacy UTMI Links with a ULPI bridge
`Internal 5V cable short-circuit protection of ID, DP and DM lines to VBUS or ground
`13MHz Reference Clock operation
- 0 to 3.6V input drive tolerant
- Able to accept "noisy" clock sources
`Internal low jitter PLL for 480MHz Hi-Speed USB operation
`Internal detection of the value of resistance to ground on the ID pin
`Integrated battery to 3.3V LDO regulator
- 2.2uF bypass capacitor
- 100mV dropout voltage
`Integrated ESD protection circuits
- Up to +-15kV without any external devices
`Carkit UART mode for non-USB serial data transfers
`Industrial Operating Temperature -40°C to +85°C
`Packaging Options
- 24 pin QFN lead-free RoHS compliant package (4 x 4 x 0.90 mm height)




Description

The USB3318 is targeted for any application where a Hi- Speed USB connection is desired and when board space, power, and interface pins must be minimized.
The USB3318 is well suited for:
·Cell Phones
·PDAs
·MP3 Players
·GPS Personal Navigation
·Scanners
·External Hard Drives
·Digital Still and Video Cameras
·Portable Media Players
·Entertainment Devices
·Printers
·Set Top Boxes
·Video Record/Playback Systems
·IP and Video Phones
·Gaming Consoles
·POS Terminals