T7906E

Features: • Besides the serial IEEE-1355 link, the T7906E provides several different interface types: Host interface The host interface provides 8 multiplexed data and address lines to program and control the T7906E locally FIFO interface The FIFO interface provides the control signals FULL,...

product image

T7906E Picture
SeekIC No. : 004511494 Detail

T7906E: Features: • Besides the serial IEEE-1355 link, the T7906E provides several different interface types: Host interface The host interface provides 8 multiplexed data and address lines to program...

floor Price/Ceiling Price

Part Number:
T7906E
Supply Ability:
5000

Price Break

  • Qty
  • 1~5000
  • Unit Price
  • Negotiable
  • Processing time
  • 15 Days
Total Cost: $ 0.00

SeekIC Buyer Protection PLUS - newly updated for 2013!

  • Escrow Protection.
  • Guaranteed refunds.
  • Secure payments.
  • Learn more >>

Month Sales

268 Transactions

Rating

evaluate  (4.8 stars)

Upload time: 2024/11/8

Payment Methods

All payment methods are secure and covered by SeekIC Buyer Protection PLUS.

Notice: When you place an order, your payment is made to SeekIC and not to your seller. SeekIC only pays the seller after confirming you have received your order. We will also never share your payment details with your seller.
Product Details

Description



Features:

• Besides the serial IEEE-1355 link, the T7906E provides several different interface types:
Host interface The host interface provides 8 multiplexed data and address lines to program and control the T7906E locally
FIFO interface The FIFO interface provides the control signals FULL, WRITE, EMPTY and READ depending on the direction of the data flow (receive / transmit)
ADC interface The ADC interface allows to connect an ADC with a width of up to 16 bits directly to the T7906E
DAC interface The DAC interface provides up to 16 bits data lines and the required control signals. The data to be sent to the DAC are stored until a command "start DAC" is received
RAM interface The RAM interface provides a 16-bit data bus and a 16-bit address bus. Four chip select allow to address 4 different memory partitions. The memory interface can be programmed to use up to 7 wait states
UART interface Two independent UART interfaces are included. One UART uses dedicated I/O lines whereas the second UART is sharing its pins with the GPIO port
General purpose I/O This general Purpose Interface provides up to 24 bidirectional signal lines. The direction of each GPIO line can be set individually via register
Timer / Event Counter Two 32-Bit on-chip timers are available. Each timer provides a 32-Bit counter and a 32-Bit reload register. The two timers can be operated independently or cascaded
JTAG (IEEE 1149.1) For testing purposes, a standard IEEE 1149.1 interface is provided. It supports the JTAG function Bypass, Extest, Sample/preload, All-tristate and IDCode
• Designed on Atmel MG1090E sea of gates matrix and packaged into MQFPF100
• Also called SMCS Lite (or SMCS116)



Pinout

Parameter
Symbol
Value
Unit
Supply voltage
VCC
-0,5 to +7
V
I/O Voltage
-0,5 to Vcc+0,5
V
Operating Temperature Range (Ambient)
TA
-55 to +125
°C
Junction Temperature
TJ
Tj < TA+20
°C
Storage temperatureRange
Tstg
-65 to +150
°C
Thermal Resistance
Rthje
1
°C/W
 
Rthja)
35
°C/W
Stresses above those listed may cause permanent damage to the device.


Description

The T7906E provides one IEEE-1355 serial communication link with 0 to 200 Mbit/s data transmit rate. It supports both the standard IEEE-1355 link protocol (transparent mode) as well as the header generation required for the enhanced transaction layer of the TSS901E. This protocol uses specific protocol headers that can be generated by the T7906E without requiring an external host controller. These headers are stored in specific header registers which allows headers with a length of 0 (equaling the transparent mode) to eight bytes per packet. Packetization of data sent by the T7906E over the link is also done automatically according to the settings of a packet length register.

Another feature provided by the transaction layer supported by the T7906E is an automatic checksum generation on the link. This is generated and checked automatically by the T7906E without requiring support from a host or other external source. Errors on the link are flagged and a special error packet is sent over the link to signal the error condition.

Programming the T7906E internal registers is done via the IEEE-1355 link. All internal registers are 8-bit wide addressable. Two simple commands (read and write) suffice to access all functions and registers of the T7906E.




Customers Who Bought This Item Also Bought

Margin,quality,low-cost products with low minimum orders. Secure your online payments with SeekIC Buyer Protection.
Power Supplies - Board Mount
LED Products
Line Protection, Backups
Optical Inspection Equipment
View more