PIC18F87J10

Features:

• Oscillator Selection
• Resets:
- Power-on Reset (POR)
- Power-up Timer (PWRT)
- Oscillator Start-up Timer (OST)
- Brown-out Reset (BOR)
• Interrupts
• Watchdog Timer (WDT)
• Fail-Safe Clock Monitor
• Two-Speed Start-up
• Code Protection
• In-Circuit Serial Programming

Specifications

Parameter Name	Value
Program Memory Type	Flash
Program Memory (KB)	128
CPU Speed (MIPS)	10
RAM Bytes	3,936
Digital Communication Peripherals	2-A/E/USART, 2-MSSP(SPI/I2C)
Capture/Compare/PWM Peripherals	2 CCP, 3 ECCP
Timers	2 x 8-bit, 3 x 16-bit
ADC	15 ch, 10-bit
Comparators	2
Temperature Range (C)	-40 to 85
Operating Voltage Range (V)	2 to 3.6
Pin Count	80

Absolute Maximum Ratings(†)

Ambient temperature under bias...............................................................................................-40°C to +125°C
Storage temperature ............................................................................................................... -65°C to +150°C
Voltage on any digital-only I/O pin with respect to V_SS (except V_DD and MCLR) ............................... -0.3V to 6.0V
Voltage on any combined digital and analog pin with respect to V_SS (except V_DD and MCLR).-0.3V to (V_DD + 0.3V)
Voltage on VDDCORE with respect to V_SS.......................................................................................... -0.3V to 2.75V
Voltage on V_DD with respect to V_SS ................................................................................................... -0.3V to 3.6V
Voltage onMCLR with respect to V_SS (Note 2) ........................................................................................ 0V to 4.0V
Total power dissipation (Note 1) ......................................................................................................................1.0W
Maximum current out of V_SS pin ...................................................................................................................300 mA
Maximum current into V_DD pin .......................................................................................................................250 mA
Maximum output current sunk by PORTB and PORTC I/O pins...........................................................................25 mA
Maximum output current sunk by PORTD, PORTE and PORTJ I/O pins .................................................................8 mA
Maximum output current sunk by PORTA, PORTF, PORTG and PORTH I/O pins ....................................................2 mA
Maximum output current sourced by PORTB and PORTC I/O pins ......................................................................25 mA
Maximum output current sourced by PORTD, PORTE and PORTJ I/O pins..............................................................8 mA
Maximum output current sourced by PORTA, PORTF, PORTG and PORTH I/O pins ................................................2 mA
Maximum current sunk by all ports ...................................................................................................................200 mA
Maximum current sourced by all ports ..............................................................................................................200 mA

Note 1: Power dissipation is calculated as follows:
Pdis = V_DD x {I_DD I_OH} + {(V_DD V_OH) x I_OH} + (V_OL x I_OL)
2: Voltage spikes below VSS at theMCLR pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to theMCLR pin, rather than pulling this pin directly to V_SS.

† NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.

Description

PIC18F87J10 is Ideal for cost sensitive applications that benefit from the availability of four serial ports: two synchronous serial ports (I2C? and SPI?) and two asynchronous (LIN capable) serial ports. Large amounts of Flash program memory and RAM make PIC18F87J10  ideal for instrumentation panels, TCP/IP enabled embedded applications as well as metering, industrial control and monitoring applications. While operating up to 40 MHz at 3V, this family of general purpose devices targets cost sensitive designs with 1k Flash endurance, emulated EEPROM, and external crystal or clock source.