HA16174P

Features:

• Maximum ratings
- Power-supply voltage Vcc: 24 V
- Operating junction temperature Tjopr: 40 to 125
• Electrical characteristics
- VREF output voltage VREF: 5.0 V ± 3%
- UVLO operation start voltage VH: 10.5 ± 0.7 V
- UVLO operation stop voltage VL: 9.0 ± 0.5 V
- PFC output maximum ON duty Dmax-out: 95% (typ.)
• Functions
- Continuous conduction mode
- Hold function of PFC operation on momentary outage (PFC hold function)
- Over voltage detection
- Over current detection
- Soft start
- Feedback loop disconnection detection
- Power Good signal output (open-drain output)
- PFC function on/off control
- Package lineup: SOP-16 and DILP-16


Pinout




Specifications

Item	Symbol	Ratings	Unit	Note
Supply voltage	VCC	24	V
OUT peak current	Ipk-out	±1.0	A	3
OUT DC current	Idc-out	±0.1	A
Terminal voltage	Vi-group1	0.3 to Vcc	V	4
	Vi-group2	0.3 to Vref	V	4
CAO voltage	Vcao	0.3 to Vcaoh	V
EO voltage	Veo	0.3 to Veoh	V
DELAY voltage	Vdelay	0.3 to +6.5	V
PFC-ON voltage	Vpfc-on	0.3 to +6.5	V
PFC-ON clamp current	Ipfc-on-clamp	300	µA
RT current	Irt	200	µA
CT current	Ict	±800	µA
IAC current	Iiac	1	mA
CS voltage	Vi-cs	1.5 to 0.3	V
VREF current	Io-ref	5	mA
PG current	Io-pg	5	mA
PGADJ voltage	Vpgadj	2.3	V
Power dissipation	Pt	1	W	6,7
Operating junction temperature	Tj-opr	40 to 125
Storage temperature	Tstg	55 to 150

Notes 1. Rated voltages are with reference to the GND pin.
          2. For rated currents, inflow to the IC is indicated by (+), and outflow by ().
          3. The transient current when driving a capacitive load.
          4. This is the rated voltage for the following pins: OUT, PG
          5. This is the rated voltage for the following pins: VREF, FB, IAC, SS, RT, CT
          6. HA16174P (DILP) type: ja = 120/W
          7. HA16174FP (SOP) type: ja = 120/W
              This is value mounted on glass epoxy board of 10% wiring density and 40 mm * 40 mm * 1.6 mm.


Description

The HA16174P/FP is a power-factor correction (PFC) controller IC.

This  HA16174P/FP   IC adopts continuous conduction mode as PFC operation.

Various functions of  HA16174P/FP   such as over voltage detection, over current detection, soft start, feedback-loop disconnection detection, Power Good signal output, and holding function of PFC operation through momentary outage (PFC hold function) are incorporated in a single chip. This eliminates a significant amount of external circuitry.

The  HA16174P/FP  PFC function enables the continuation of PFC operation for a specified period when a momentary outage occurs, so that quick recovery after a sufficiently momentary outage is achieved*. The continuance time can be adjusted by an external capacitance.

The  HA16174P/FP  PFC output voltage is monitored by checking the Power Good signal. When the power-factor correction is "good," the Power Good signal is output after a delay time to secure stabilization of the PFC output voltage; when the power factor correction is not good, the output is stopped immediately. The delay time and power good stop level are adjustable by using an external circuit.

 HA16174P/FP  PFC operation can be turned on and off by an external control signal. By using this function, PFC operation can be disabled at low input voltage, allowing remote control from the secondary side. A soft-start control pin provides for the easy adjustment of soft-start operation, and can be used to prevent overshooting of the output voltage.

*: For details on the  HA16174P/FP  PFC hold function, refer to page 19.