Features: ` Low "ON" resistance:
80 (typ.) at VCC - VEE = 4.5 V
70 (typ.) at VCC - VEE = 6.0 V
60 (typ.) at VCC - VEE = 9.0 V
` Logic level translation:
to enable 5 V logic to communicate
with ± 5 V analog signals
` Typical "break before make" built in
` Output capability: non-standard
` ICC category: MSI Application· Analog multiplexing and demultiplexing
· Digital multiplexing and demultiplexing
· Signal gatingPinout
Specifications
| SYMBOL |
PARAMETER |
MIN. |
MAX. |
UNIT |
CONDITIONS |
| VCC |
DC supply voltage |
-0.5 |
+11.0 |
V |
|
| ±IIK |
DC digital input diode current |
|
20 |
mA |
for VI < -0.5 V or VI > VCC + 0.5 V |
| ±ISK |
DC switch diode current |
|
20 |
mA |
for VS < -0.5 V or VS > VCC + 0.5 V |
| ±IS |
DC switch current |
|
25 |
mA |
for -0.5 V < VS < VCC + 0.5 V |
| ±IEE |
DC VEE current |
|
20 |
mA |
|
| ±ICC; ±IGND |
DC VCC or GND current |
|
50 |
mA |
|
| Tstg |
storage temperature range |
-65 |
+150 |
°C |
|
| Ptot |
power dissipation per package
plastic DIL |
|
750 |
mW |
for temperature range: -40 to + 125 °C
74HC/HCT
above + 70 °C: derate linearly with 12 mW/K |
| |
plastic mini-pack (SO) |
|
500 |
mW |
above + 70 °C: derate linearly with 8 mW/K |
| PS |
power dissipation per switch |
|
100 |
mW |
|
Note to ratings
To avoid drawing VCC current out of terminals nZ, when switch current flows in terminals nYn, the voltage drop across
the bidirectional switch must not exceed 0.4 V. If the switch current flows into terminals nZ, no VCC current will flow out
of terminals nYn. In this case there is no limit for the voltage drop across the switch, but the voltages at nYn and nZ may not exceed VCC or VEE.
DescriptionThe 74HC4351 is high-speed Si-gate CMOS devices. They are specified in compliance with JEDEC standard no. 7A.
The 74HC4351 is 8-channel analog multiplexers/demultiplexers with three select inputs (S0 to S2), two enable inputs (E1 and E2), a latch enable input (LE), eight independent inputs/outputs (Y0 to Y7) and a common input/output (Z).
With E1 LOW and E2 is HIGH, one of the eight switches is selected (low impedance ON-state) by S0 to S2. The data at the select inputs may be latched by using the active LOW latch enable input (LE). When LE is HIGH the latch is transparent. When either of the two enable inputs, E1 (active LOW) and E2 (active HIGH), is inactive, all 8 analog switches are turned off.
VCC and GND of the 74HC4351 are the supply voltage pins for the digital control inputs (S0 to S2, LE, E1 and E2). The VCC to GND ranges are 2.0 to 10.0 V for HC and 4.5 to 5.5 V for HCT. The analog inputs/outputs (Y0 to Y7, and Z) can swing between VCC as a positive limit and VEE as a negative limit.
VCC - VEE may not exceed 10.0 V.
For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground).
74HC4351 Data Sheet
