X9110

Features: • 1024 Resistor Taps 10-Bit Resolution• SPI Serial Interface for write, read, and transfer operations of the potentiometer• Wiper Resistance, 40 Typical @ 5V• Four Non-Volatile Data Registers• Non-Volatile Storage of Multiple Wiper Positions• Power-on...

product image

X9110 Picture
SeekIC No. : 004547473 Detail

X9110: Features: • 1024 Resistor Taps 10-Bit Resolution• SPI Serial Interface for write, read, and transfer operations of the potentiometer• Wiper Resistance, 40 Typical @ 5V• Four...

floor Price/Ceiling Price

Part Number:
X9110
Supply Ability:
5000

Price Break

  • Qty
  • 1~5000
  • Unit Price
  • Negotiable
  • Processing time
  • 15 Days
Total Cost: $ 0.00

SeekIC Buyer Protection PLUS - newly updated for 2013!

  • Escrow Protection.
  • Guaranteed refunds.
  • Secure payments.
  • Learn more >>

Month Sales

268 Transactions

Rating

evaluate  (4.8 stars)

Upload time: 2024/11/13

Payment Methods

All payment methods are secure and covered by SeekIC Buyer Protection PLUS.

Notice: When you place an order, your payment is made to SeekIC and not to your seller. SeekIC only pays the seller after confirming you have received your order. We will also never share your payment details with your seller.
Product Details

Description



Features:

• 1024 Resistor Taps 10-Bit Resolution
• SPI Serial Interface for write, read, and transfer operations of the potentiometer
• Wiper Resistance, 40 Typical @ 5V
• Four Non-Volatile Data Registers
• Non-Volatile Storage of Multiple Wiper Positions
• Power-on Recall. Loads Saved Wiper Position on Power-up
• Standby Current < 3A Max
• System VCC: 2.7V to 5.5V Operation
• Analog V+/V-: -5V to +5V
• 100k End to End Resistance
• 100 yr. Data Retention
• Endurance: 100, 000 Data Changes Per Bit Per Register
• 14 Ld TSSOP
• Dual Supply Version of the X9111
• Low Power CMOS
• Pb-Free Plus Anneal Available (RoHS Compliant)





Application

• Vary the gain of a voltage amplifier
• Provide programmable dc reference voltages for comparators and detectors
• Control the volume in audio circuits
• Trim out the offset voltage error in a voltage amplifier circuit
• Set the output voltage of a voltage regulator
• Trim the resistance in Wheatstone bridge circuits
• Control the gain, characteristic frequency and Q-factor in filter circuits
• Set the scale factor and zero point in sensor signal conditioning circuits
• Vary the frequency and duty cycle of timer ICs
• Vary the dc biasing of a pin diode attenuator in RF circuits
• Provide a control variable (I, V, or R) in feedback circuits
• Adjust the contrast in LCD displays
• Control the power level of LED transmitters in communication systems
• Set and regulate the DC biasing point in an RF power amplifier in wireless systems
• Control the gain in audio and home entertainment systems
• Provide the variable DC bias for tuners in RF wireless systems
• Set the operating points in temperature control systems
• Control the operating point for sensors in industrial systems
• Trim offset and gain errors in artificial intelligent systems





Pinout

  Connection Diagram




Specifications

Temperature under bias . . . . . . . . . . . . . . . . -65°C to +135°C
Storage temperature . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Voltage on SCK any address input
with respect to VSS . . . . . . . . . . . . . . . . . . . . . . . . -1V to +7V
Voltage on V+ (referenced to VSS) (Note 4) . . . . . . . . . . . . . 10V
Voltage on V- (referenced to VSS) (Note 4) . . . . . . . . . . . . . -10V
(V+) - (V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V
Any Voltage on RH/RL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V+
Any Voltage on RL/RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V-
Lead temperature (soldering, 10s). . . . . . . . . . . . . . . . . . 300°C
IW (10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±6mA






Description

The X9110 integrates a single digitally controlled potentiometer (XDCP) on a monolithic CMOS integrated circuit.

The X9110 digital controlled potentiometer is implemented using 1023 resistive elements in a series array. Between each element are tap points connected to the wiper terminal through switches. The position of the wiper on the array is controlled by the user through the SPI bus interface. The potentiometer has associated with it a volatile Wiper Counter Register (WCR) and four non-volatile Data Registers that can be directly written to and read by the user. The contents of the WCR controls the position of the wiper on the resistor array though the switches. Power-up recalls the contents of the default data register (DR0) to the WCR.

The X9110 XDCP can be used as a three-terminal potentiometer or as a two terminal variable resistor in a wide variety of applications including control, parameter adjustments, and signal processing.






Customers Who Bought This Item Also Bought

Margin,quality,low-cost products with low minimum orders. Secure your online payments with SeekIC Buyer Protection.
Power Supplies - Board Mount
Optical Inspection Equipment
Motors, Solenoids, Driver Boards/Modules
Line Protection, Backups
Programmers, Development Systems
Semiconductor Modules
View more