Features: `Fully integrated charger with FET pass transistor, reverse-blocking diode, sense resistor, timer, and thermal protection
`Battery voltage controlled to 1% accuracy
`Programmable pre charge, fast charge & termination current over wide range, with analog current control reference input for design fl exibility
`Up to 1.5A continuous charge current
`Input voltage range from 3V to 14V
`Soft-start reduces start-of-charge adapter load transients
`NTC thermistor sense input and adjustable cold temperature threshold
`Adjustable 2 - 6 hour programmable charge timer
`0.1A battery drain current in shutdown and monitor modes
`Small 4mm x 4mm 16 lead MLPQ package
`Over-current protection in all modes
`Over-voltage protection
`Remote Kelvin sensing at the battery terminals
`Status indicators for charger-present, charger-active, over-voltage fault, and error notifi cation
Application·Cellular phones
·PDAs
·Handheld meters
·Charging stations
·Handheld computers
·Digital cameras
·Programmable current sourcePinout
Specifications
| Parameter |
Symbol |
Maximum |
Units |
| VCC, CTO, NTC to GND |
|
-0.3 to 14.0 |
V |
VOUT, BSEN, RTIM, AFC, IPRGM, CPB, CHRGB, OVPB,
ITERM, FLTB, to GND |
|
-0.3 to +6.0 |
V |
| RGND to GND |
|
-0.3 to 0.3 |
V |
| VOUT Output Current |
IVOUT |
1.5 |
A |
| Power Dissipation MLP (Derate 20mW/ above 85) |
Pd |
2 |
W |
| Thermal Impedance, Junction to Ambient(1) |
JA |
48 |
/W |
| Junction Temperature |
TJ |
150 |
|
| Operating Ambient Temperature Range |
TA |
-40 to +85 |
|
| IR Refl ow Temperature |
TLEAD |
260 |
|
| Storage Temperature Range |
TSTG |
-65 to 150 |
|
| VOUT short to GND |
|
Continuous |
|
| ESD Protection Level(2) |
V ESD |
2 |
kV |
Notes:
1) Calculated from package in still air, mounted to 3" x 4.5", 4 layer FR4 PCB with thermal vias under the exposed pad per JESD51 standards.
2) Tested according to JEDEC standard JESD22-A114-B.
DescriptionThe SC804 is a fully integrated full-feature, single cell constant-current/constant-voltag e (CC/CV) Lithium-Ion battery charger. With an integrated timer and complete charge control algorithm, the SC804 is ideal for standalone charger applications. The SC804 contains programmable pre-charge, fast-charge and termination current settings. The SC804 can be programmed to terminate charging based on the output current or the time-out of the programmable timer. The fast charge current is typically set with an external resistor, but it can also be adjusted by applying an analog voltage to the AFC pin. This feature allows use of a micro controller to set charging current via a DAC output.
The SC804's 14V input voltage range eliminates the need for additional protection circuitry required by other 5V chargers to protect against faulty adapters. The SC804 also incorporates an under-voltage lockout falling threshold of 3V so that charging will continue if the input supply goes into a current-limited mode.
Reference ground and battery sense inputs are provided to eliminate voltage drops during charging due to high charging currents.
The output voltage to the battery is controlled to within 1% of the programmed voltage. The SC804 can also function as a general purpose current source or as a current source for charging nickel-cadmium (NiCd) and nickelmetal- hydride (NiMH) batteries.
SC804 Data Sheet
