PVX-4140

Features: • 0 to ±3500V Pulse Output• 25ns Rise And Fall Times• 60ns to DC Pulse Width• >30KHz Pulse Repetition Frequency• Optimized To Drive Deflection Plates, Grids, Pockels Cells And Other Capacitive Loads• Protected Against Arcs, Shorts And Load Transient...

product image

PVX-4140 Picture
SeekIC No. : 004467328 Detail

PVX-4140: Features: • 0 to ±3500V Pulse Output• 25ns Rise And Fall Times• 60ns to DC Pulse Width• >30KHz Pulse Repetition Frequency• Optimized To Drive Deflection Plates, Grid...

floor Price/Ceiling Price

Part Number:
PVX-4140
Supply Ability:
5000

Price Break

  • Qty
  • 1~5000
  • Unit Price
  • Negotiable
  • Processing time
  • 15 Days
Total Cost: $ 0.00

SeekIC Buyer Protection PLUS - newly updated for 2013!

  • Escrow Protection.
  • Guaranteed refunds.
  • Secure payments.
  • Learn more >>

Month Sales

268 Transactions

Rating

evaluate  (4.8 stars)

Upload time: 2024/11/25

Payment Methods

All payment methods are secure and covered by SeekIC Buyer Protection PLUS.

Notice: When you place an order, your payment is made to SeekIC and not to your seller. SeekIC only pays the seller after confirming you have received your order. We will also never share your payment details with your seller.
Product Details

Description



Features:

• 0 to ±3500V Pulse Output
• 25ns Rise And Fall Times
• 60ns to DC Pulse Width
• >30KHz Pulse Repetition Frequency
• Optimized To Drive Deflection Plates, Grids, Pockels Cells And Other Capacitive Loads
• Protected Against Arcs, Shorts And Load Transients
• Voltage And Current Monitor Outputs



Specifications

Maximum Value: ±1500 Volts (VHigh - VLow)
Minimum Value: 0 Volts
Means Of Adjustment: Controlled By Power Supply Input Voltages
Pulse Rise And Fall Time: <25ns, typically <20ns (10% to 90%)
Pulse Width: <60ns to DC, Controlled by Input Gate
Pulse Recurrence Frequency
(PRF):
Single shot to 240KHz at 1500V continuous output,
maximum limited by power dissipation (1), 5MHz Burst,
Controlled by Input Gate
Max. Average Power: 150W (VHigh + VLow), derated at 2W/°C over 25°C ambient(1)
Max. Duty Cycle: Continuous
Droop: <1%
Over/undershoot: <5%
Throughput Delay 120ns Typical
Jitter: <1ns shot-to-shot
Output Connector & Cable: SHV, With 6 feet (~1.8M) RG-62 (93W) Coaxial Cable



Description

The PVX-4140 pulse generator produces fast, high voltage wave forms to 3,500V. Optimized for high impedance capacitive loads, the PVX-4140 is well suited for driving extraction grids and deflection plates for electrostatic modulation of particle beams in time-of-flight mass spectrometers and accelerators. Its robust and versatile design also makes it well suited for pulsing or gating power tube grids, Pockels cells and Q Switches, acoustic transducers, microchannel plates, photomultiplier tubes and image intensifiers. The exceptional pulse fidelity of the PVX-4140 will optimize the performance of any system in which it is used.

The PVX-4140 generates an output voltage pulse of 3,500 volts with rise and fall times of 25ns or less, with very flat voltage pulses to DC into a capacitive load. It can generate singled-ended output pulses from ground to +3500V or from ground to 3500V, and can also generate pulses originating from a DC voltage offset from ground by using both VLow and VHigh power supply inputs. This offset can be from 3500V to +3500V, with a maximum power supply voltage differential of 3500V.

The PVX-4140 requires a user-supplied TTL gate signal, a high voltage DC power supply and optional DC offset supply inputs. The output pulse width and frequency are controlled by the gate signal. The pulse output voltage is controlled by the amplitude of the input DC power supplies.

When the input gate is high, the VHIGH supply is connected to the output. When the input gate is low, the VLOW supply is connected to the output. Therefore the PVX-4140 can be used to generate a negative-going pulse by logically inverting the input gate, so that the input gate is high until the unit is pulsed. When the input gate goes low, the VLOW input supply is connected to the output, thereby generating a negative-going pulse.

The PVX-4140 features front panel indicator LEDs to monitor the status of the pulse generator. Front panel instrument- quality voltage and current monitors provide a straightforward means to view the output voltage and current waveforms in real-time, eliminating the need for an external high voltage oscilloscope probe.

The pulse generator is a direct-coupled, air-cooled solidstate half-bridge (totem pole) design, offering equally fast pulse rise and fall times, low power dissipation, and virtually no over-shoot, under-shoot or ringing. It has over-current detection and shut-down circuitry to protect the pulse generator from potential damage due to arcs and shorts in the load or interconnect cable. All control and protection logic circuitry, support power, energy storage and output network are incorporated into the PVX-4140. It can be connected directly to the load, and does not require series or shunt resistors, impedance-matching networks between the pulser and the load, or additional energy storage (capacitor banks). All of this is taken care of within the PVX-4140.




Customers Who Bought This Item Also Bought

Margin,quality,low-cost products with low minimum orders. Secure your online payments with SeekIC Buyer Protection.
Line Protection, Backups
Sensors, Transducers
Industrial Controls, Meters
Cables, Wires
Prototyping Products
DE1
Static Control, ESD, Clean Room Products
View more