Features: • Automatic Twisted Pair Wiring Polarity Fault Detection and Correction Option
• Automatic Port Selection Option with Status Output
• Driver Preemphasis for Twisted Pair Output Data
• Crystal Controlled Clock Oscillator or External Clock Generator Option
• Digital PhaseLockedLoop (DPLL) Timing Recovery and Data Decoding
• Standby Mode with Reduced Power Consumption
• Twisted Pair Signal Quality Error (Heartbeat) Test Option
• Diagnostic Local Loop Back Option
• Transmit, Receive and Collision Detection Status Output
• FullDuplex Operation Option on Twisted Pair Port
• Twisted Pair Jabber Detection and Status Output
• Link Integrity Testing and Status Output
* MC68160B does not support all IEEE 802.3 specifications over extended temperature range. Exceptions
noted in specifications.
** MC68160B, C only support Motorola controllersApplicationThe following procedure is applicable to all three versions MC68160, MC68160B and MC68160C. References to the MC68160 includes all the versions.
Resetting the MC68160 after power up.
In some applications, after initial power up, the MC68160 may not be able to transmit or receive data. This is usually
caused by the LOOP and TPFULDL control lines being active at the same time. This is an illegal condition during normal operation, it places the MC68160 into the production test mode.
To exit the test mode and return to normal: Set LOOP low, TPFULDL high and TPSQEL low. Then, while keeping
TPSQEL low, raise LOOP after 300 ms lower TPFULDL. This will put the MC68160 into test mode but also resets the
MC68160. After 500 ms lower LOOP to get out of the test mode. TPFULDL may then be deasserted if desired.
The MC68160 is now ready for operation.
A hardware implementation of this fix would be to place a pull down resistor on the TPSQEL pin. Even if test mode is
entered by accident, this ensures that zero's will be written to the test register. The hardware implementation will solve the problem if the test mode is entered because of noise on the TPSQEL pin. If the controller is toggling the MC68160 lines while it is booting up, the reset procedure must be followed.
Specifications
|
Characteristic |
Symbol |
Min |
Max |
Unit |
| Storage Temperature Range |
Tstg |
65 |
150 |
|
Power Supply Voltage Range
Analog
Digital |
VDDA
VDDD
|
|
7.0
7.0
|
V |
Voltage on any TTL compatible input pin with
respect toGround
Voltage on TPRX, ARX, or ACX input pins with
respect to Ground |
V |
0.5
0.5 |
VDD + 0.5
6.0 |
V |
| Differential Voltage on TPRX, ARX, or ACX Input Pins |
VDIFF |
6.0 |
6.0 |
V |
NOTE: Stresses in excess of the Absolute Maximum Ratings can cause permanent damage to thedevice.
Functional operation of the device is not implied at these or any other conditions inexcess of those
indicated in the operation sections of this data sheet. Exposure to AbsoluteMaximum Ratings conditions
for extended periods can adversely affect device reliability.DescriptionThe MC68160, B and C Enhanced Ethernet Interface Circuit is a BiCMOS device which supports both IEEE 802.3* Access Unit Interface (AUI) and 10BASET Twisted Pair (TP) Interface media connections through external
isolation transformers. MC68160B encodes NRZ data to Manchester data and supplies the signals which are required for data communication via 10BASET or AUI interfaces. The MC68160, B and C gluelessly interface to the Ethernet controller contained in the MC68360 Quad Integrated Communications Controller (QUICC) device. The MC68160 also interfaces easily to most other industrystandard IEEE 802.3 LAN controllers.** Prior to twisted pair data reception, Smart Squelch circuitry qualifies input signals for correct amplitude, pulse width, and sequence requirements.
MC68160B Data Sheet
