IC LED DRIVER LINEAR 16-SOIC
SeekIC Buyer Protection PLUS - newly updated for 2013!
268 Transactions
All payment methods are secure and covered by SeekIC Buyer Protection PLUS.
US $4.26 - 6.3 / Piece
Counter Shift Registers 5V ECL 8-Bit Binary Up Synchronous
Series: | - | Manufacturer: | ON Semiconductor |
Constant Current: | - | Type: | - |
Constant Voltage: | - | Topology: | - |
Number of Outputs: | 1 | Efficiency: | - |
Internal Driver: | Yes | Package / Case : | BGA-56 |
Current - Output / Channel: | - | Type - Primary: | General Purpose |
Type - Secondary: | - | Frequency: | 300MHz |
Internal Switch(s): | - | Voltage - Supply: | +5V, -5.2V |
Voltage - Output: | - | Mounting Type: | Surface Mount |
Package / Case: | 16-SOIC (0.154", 3.90mm Width) | Supplier Device Package: | 16-SOIC |
Packaging: | Tube |
Symbol | Parameter | Value | Unit |
VEE | Power Supply (VCC = 0V) | 7.0 to 0 | VDC |
V I | Input Voltage (VCC = 0V) | 0 to 6.0 | VDC |
Iout | Output Current Continuous Surge |
100 110 |
mA |
T A | Operating Temperature Range | 40 to +85 | °C |
V EE | Operating Range (VCC = 0) | 5.5 to 4.5 | VDC |
The MC10SX1130 incorporates open collector outputs with a capability of driving peak currents of 100mA. Since the output current switching circuitry simply switches current between the complementary outputs, thedynamic switching demands on the system power supply are greatly reduced. In addition, because the design is pure bipolar, the MC10SX1130 current drain is insensitive to the data pattern and frequency of operation.
The LED drive current of MC10SX1130 is adjustable through the selection of an external set resistor, RSET. In addition, to allow for open loop compensation for the LED's negative optical output power tracking over temperature, a circuit is included to provide an adjustable positive temperature tracking coefficient to the LED drive current. MC10SX1130 is controlled through the selection of an external resistor, RTCO.
The MC10SX1130 incorporates novel pulse stretching circuitry which is intended to compensate for the turn-on delay and rise and fall time asymmetry inherent in LED devices. The stretch circuitry of MC10SX1130 can be used to pre-distort the input signal pulse width to minimize the duty cycle distortion of the transmitted optical eye pattern. The stretch circuitry supports three different selections of pre-distortion. This choice is accomplished through a unique 'tri-state' input which can be left open, tied to VCC, or tied to VEE to determine the pre-distortion amount.
The MC10SX1130 provides a VBB output for either single-ended use or as a DC bias for AC coupling the signal into the device. The VBB pin should only be used as a bias for the MC10SX1130 as its current sink/source capability is limited. Whenever used, the VBB pin should be bypassed to ground via a 0.01mF capacitor.
Technical/Catalog Information | MC10SX1130D |
Vendor | ON Semiconductor |
Category | Integrated Circuits (ICs) |
Package / Case | 16-SOIC (3.9mm Width) |
Packaging | Tube |
Current - Output / Channel | 100mA |
Number of Outputs | 1 |
Type | Linear (Non-Switching) |
Voltage - Supply | +5V, -5.2V |
Voltage - Output | - |
Topology | Smart |
Frequency | 300MHz |
Operating Temperature | -40°C ~ 85°C |
Efficiency | - |
Lead Free Status | Contains Lead |
RoHS Status | RoHS Non-Compliant |
Other Names | MC10SX1130D MC10SX1130D MC10SX1130DOS ND MC10SX1130DOSND MC10SX1130DOS |