Features: ` Complies with Universal Serial Bus Specification Rev. 2.0
` The Host Controller portion of the ISP1161A1 supports data transfer at full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s)
` The Device Controller portion of the ISP1161A1 supports data transfer at full-speed (12 Mbit/s)
` Combines the HC and the DC in a single chip
` On-chip DC complies with most USB device class specifications
` Both the HC and the DC can be accessed by an external microprocessor via separate I/O port addresses
` Selectable one or two downstream ports for the HC and one upstream port for the DC
` High-speed parallel interface to most of the generic microprocessors and Reduced Instruction Set Computer (RISC) processors such as:
` Hitachi® SuperH™ SH-3 and SH-4
` MIPS-based™ RISC
` ARM7™, ARM9™, StrongARM®
` Maximum 15 Mbyte/s data transfer rate between the microprocessor and the HC,11.1 Mbyte/s data transfer rate between the microprocessor and the DC
` Supports single-cycle and burst mode DMA operations
` Up to 14 programmable USB endpoints with 2 fixed control IN/OUT endpoints for the DC
` Built-in separate FIFO buffer RAM for the HC (4 kbytes) and DC (2462 bytes)
` Endpoints with double buffering to increase throughput and ease real-time data transfer for both DC transfers and HC isochronous (ISO) transactions
` 6 MHz crystal oscillator with integrated PLL for low EMI
` Controllable LazyClock (100 kHz ± 50 %) output during 'suspend'
` Clock output with programmable frequency (3 MHz to 48 MHz)
` Software controlled connection to USB bus (SoftConnect) on upstream port for the DC
` Good USB connection indicator that blinks with traffic (GoodLink) for the DC
` Software selectable internal 15 k pull-down resistors for HC downstream ports
` Dedicated pins for suspend sensing output and wake-up control input for flexible applications
` Global hardware reset input pin and separate internal software reset circuits for HC and DC
` Operation from a 5 V or a 3.3 V power supply
` Operating temperature range -40 °C to +85 °C
` Available in two LQFP64 packages (SOT314-2 and SOT414-1).Application· Personal Digital Assistant (PDA)
· Digital camera
· Third-generation (3-G) phone
· Set-Top Box (STB)
· Information Appliance (IA)
· Photo printer
· MP3 jukebox
· Game console.Pinout
Specifications
| Symbol |
Parameter |
Conditions |
Min |
Max |
Unit |
| VCC(5V) |
supply voltage to pin VCC |
|
-0.5 |
+6.0 |
V |
| VCC(3.3V) |
supply voltage to pin VREG(3.3) |
|
-0.5 |
+4.6 |
V |
| VI |
input voltage |
|
-0.5 |
+6.0 |
V |
| Ilu |
latch-up current |
VI < 0 or VI > VCC |
- |
100 |
mA |
| Vesd |
electrostatic discharge voltage |
ILI < 1 A [1] |
-2000 |
+2000 |
V |
| Tstg |
storage temperature |
|
-60 |
+150 |
|
[1] Equivalent to discharging a 100 pF capacitor via a 1.5 k resistor (Human Body Model).DescriptionThe ISP1161A1 is a single-chip Universal Serial Bus (USB) Host Controller (HC) and Device Controller (DC). The Host Controller portion of the ISP1161A1 complies with Universal Serial Bus Specification Rev. 2.0, supporting data transfer at full-speed (12 Mbit/s) and low-speed (1.5 Mbit/s). The Device Controller portion of the ISP1161A1 also complies with Universal Serial Bus Specification Rev. 2.0, supporting data transfer at full-speed (12 Mbit/s). These two USB controllers, the HC and the DC, share the same microprocessor bus interface. They have the same data bus, but different I/O locations. They also have separate interrupt request output pins, separate DMA channels that include separate DMA request output pins and DMA acknowledge input pins. This makes it possible for a microprocessor to control both the USB HC and the USB DC at the same time.
The ISP1161A1 provides two downstream ports for the USB HC and one upstream port for the USB DC. Each downstream port has an overcurrent (OC) detection input pin and power supply switching control output pin. The upstream port has a VBUS detection input pin.The ISP1161A1 also provides separate wake-up input pins and suspended status output pins for the USB HC and the USB DC, respectively. This makes power management flexible. The downstream ports for the HC can be connected with any USB compliant devices and hubs that have USB upstream ports.The upstream port for the DC can be connected to any USB compliant USB host and USB hubs that have USB downstream ports.
The HC is adapted from the Open Host Controller Interface Specification for USB Release 1.0a, referred to as OHCI in the rest of this document.
The DC is compliant with most USB device class specifications such as Imaging Class, Mass Storage Devices, Communication Devices, Printing Devices and Human Interface Devices.
The ISP1161A1 is well suited for embedded systems and portable devices that require a USB host only, a USB device only, or a combination of a configurable USB host and USB device. The ISP1161A1 brings high flexibility to the systems that have it built-in. For example, a system that uses an ISP1161A1 allows it not only to be connected to a PC or USB hub with a USB downstream port, but also to be connected to a device that has a USB upstream port such as a USB printer, USB camera, USB keyboard or a USB mouse. Therefore, the ISP1161A1 enables point-to-point connectivity between embedded systems. An interesting application example is to connect an ISP1161A1 HC with an ISP1161A1 DC.
Consider an example of an ISP1161A1 being used in a Digital Still Camera (DSC) design. Figure 1 shows an ISP1161A1 being used as a USB DC. Figure 2 shows an ISP1161A1 being used as a USB HC. Figure 3 shows an ISP1161A1 being used as a USB HC and a USB DC at the same time
ISP1161A1 Data Sheet
