Features: • High Speed (480Mbps) and Full Speed (12Mbps) Signaling Capability per USB 2.0
• Low Distortion Negative Signal Capability
• Control Pin to Open all Switches and Enter Low Power State
• Low Distortion Headphone Audio Signals
- THD+N at 20mW into 32 Load . . . . . . . . . . . . . <0.1%
• Cross-talk Audio Channels (20Hz to 20kHz) . . . . . -110dB
• Single Supply Operation (VDD) . . . . . . . . . . . . 2.5V to 5.5V
• -3dB Bandwidth USB Switches . . . . . . . . . . . . . . . 630MHz
• Available in TQFN and TDFN Packages
• Pb-Free Plus Anneal (RoHS Compliant)
• Compliant with USB 2.0 Short Circuit Requirements Without Additional External ComponentsApplication• MP3 and Other Personal Media Players
• Cellular/Mobile Phones
• PDA's
• Audio/USB SwitchingPinout
SpecificationsVDD to GND . . . . . . . . . . . . . . . . . .. . . . . . -0.3 to 6.0V
Input Voltages
D+, D-, L, R (Note 2) . . . . . . . .. - 2V to ((VDD) + 0.3V)
IN (Note 2). . . . . . . . . . . . . . . . . . . . . . . . -2V to 5.5V
CTRL (Note 2) . . . . . . . . . . .. . . -0.3 to ((VDD) + 0.3V)
Output Voltages
COM-, COM+ (Note 2) . . . . . .. . -2V to ((VDD) + 0.3V)
Continuous Current (Audio Switches). . . . . . . ±150mA
Peak Current (Audio Switches)
(Pulsed 1ms, 10% Duty Cycle, Max). . . . . . . ±300mA
Continuous Current (USB Switches). . . . . . . . . ±40mA
Peak Current (USB Switches)
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . ±100mA
ESD Rating:
HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . >7kV
MM . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . >400V
CDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .>1.4kV
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty.
NOTES:
2. Signals on D+, D-, L, R, COM-, COM+, CTRL, IN exceeding VDD or GND by specified amount are clamped. Limit current to maximum current ratings.
3. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
DescriptionThe Intersil ISL54206A dual SPDT (Single Pole/Double Throw) switches combine low distortion audio and accurate
USB 2.0 high speed data (480Mbps) signal switching in the same low voltage device. When operated with a 2.7V to 3.6V single supply these analog switches allow audio signal swings below-ground, allowing the use of a common USB and audio headphone connector in Personal Media Players and other portable battery powered devices.
The ISL54206A logic control pins are 1.8V compatible which allows for control via a standard controller. With a VDD voltage in the range of 2.7V to 3.6V the IN pin voltage can exceed the VDD rail allowing for the USB 5V VBUS voltage from a computer to directly drive the IN pin to switch between the audio and USB signal sources in the portable device. The part has an audio enable control pin to open all the switches and put the part in a low power state.
The ISL54206A is available in a small 10 Ld 2.1mmx1.6mm ultra-thin TQFN package and a 10 Ld 3mmx3mm TDFN package. It operates over a temperature range of -40 to +85.
ISL54206A Data Sheet
