Operating Supply Voltage
:
Operating Supply Current
:
Rise Time
: 150 ns
Fall Time
: 55 ns
Number of Outputs
: 1
Maximum Operating Temperature
: + 130 C
Mounting Style
: SMD/SMT
Duty Cycle (Max)
: 77 %
Switching Frequency
: 67 KHz
Package / Case
: DSO-8
Features: · Active Burst Mode for lowest Standby Power
@ light load controlled by Feedback Signal
· Fast load jump response in Active Burst Mode
· 500V Startup Cell switched off after Start Up
· 100/67kHz internally fixed switching frequency
· Auto Restart Mode for Overtemperature Detection
· Auto Restart Mode for VCC Overvoltage Detection
· Auto Restart Mode for Overload and Open Loop
· Auto Restart Mode for VCC Undervoltage
· Blanking Window for short duration high current
· User defined Soft Start
· Minimum of external components required
· Max Duty Cycle 72%
· Overall tolerance of Current Limiting < ±5%
· Internal PWM Leading Edge Blanking
· Soft switching for low EMIPinout
SpecificationsNote: Absolute maximum ratings are defined as ratings, which when being exceeded may lead to destruction of the integrated circuit. For the same reason make sure, that any capacitor that will be connected to pin 7 (VCC) is discharged before assembling the application circuit.
|
Parameter |
Symbol |
Limit Values |
Unit |
Remarks |
|
min. |
max. |
| HV Voltage |
VHV |
- |
500V |
V |
|
| VCC Supply Voltage |
VVCC |
-0.3 |
22 |
V |
|
| FB Voltage |
VFB |
-0.3 |
6.5 |
V |
|
| SoftS Voltage |
VSoftS |
-0.3 |
6.5 |
V |
|
| Gate Voltage |
VGate |
-0.3 |
22 |
V |
Internally clamped at 11.5V |
| CS Voltage |
VCS |
-0.3 |
6.5 |
V |
|
| Junction Temperature |
Tj |
-40 |
150 |
|
|
| Storage Temperature |
TS |
-55 |
150 |
|
|
| Total Power Dissipation |
PtotDSO8 |
- |
0.45 |
W |
P-DSO-8-8, Tamb < 50 |
|
PtotDIP8 |
- |
0.90 |
W |
PG-DIP-8-6, Tamb < 50 |
Thermal Resistance
Junction-Ambient |
RthJADSO8 |
- |
185 |
K/W |
P-DSO-8-8 |
|
RthJADIP8 |
- |
90 |
K/W |
PG-DIP-8-6 |
| ESD Capability(incl. HV Pin) |
VESD |
- |
3 |
kV |
Human body model 1) |
1)According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5k series resistor)
DescriptionThe F3 Controller of the ICE3BS02G provides Active Burst Mode to reach the lowest Standby Power Requirements <100mW at no load.
As the controller of the ICE3BS02G is always active during Active Burst Mode, there is an immediate response on load jumps without any black out in the SMPS. In Active Burst Mode the ripple of the output voltage can be reduced <1%.
Furthermore, to increase the robustness and safety of the system, the ICE3BS02G enters into Auto Restart Mode in the cases of Overtemperature, VCC Overvoltage, Output Open Loop or Overload and VCC Undervoltage. By means of the internal precise peak current limitation, the dimension of the transformer and the secondary diode can be lowered which leads to more cost efficiency. An adjustable blanking window prevents the IC from entering Auto Restart Mode or Active Burst Mode unintentionally in case of high load jumps.
Parameters: | Technical/Catalog Information | ICE3BS02G |
| Vendor | Infineon Technologies |
| Category | Integrated Circuits (ICs) |
| Packaging | Tube |
| Package / Case | DSO-8 |
| Power (Watts) | 450mW |
| Voltage - Input | 9 ~ 22 V |
| Voltage - Output | 500V |
| Frequency Range | 61 ~ 73kHz |
| Operating Temperature | -40°C ~ 150°C |
| Output Isolation | Isolated |
| Lead Free Status | Lead Free |
| RoHS Status | RoHS Compliant |
| Other Names | ICE3BS02G
ICE3BS02G
|
ICE3BS02G Data Sheet
