HCPL-3180

Current Transfer Ratio :
Maximum Baud Rate :
Maximum Input Diode Current :
Maximum Forward Diode Voltage : 1.8 V
Maximum Reverse Diode Voltage : 5 V
Maximum Operating Temperature : + 100 C
Minimum Operating Temperature : - 40 C
Packaging : Tube
Maximum Power Dissipation : 295 mW
Package / Case : PDIP-8


Features:

• 2 A minimum peak output current
• 250 KHz maximum switching speed
• High speed response: 200 ns max Propagation delay over temperature range
• 10 KV/us minimum common mode rejection (CMR) at V_CM=1500 V
• Under voltage lockout protection (UVLO) with hysteresis
• Wide operating temperature range: -40 to +100
• Wide V_CC operating range:10 V to 20 V
• 20 ns typ pulse width distortion
• Safety Approvals:UL approval pending 3750 V_RMS for 1 minute.CSA approval DIN EN 60747-5-2 approval pending




Application

• Plasma Display Panel (PDP)
• Distributed power architecture (DPA)
• Switch mode rectifier (SMR)
• High performance DC/DC convertor
• High performance switch mode power supply (SMPS)
• High performance uninterruptible power supply (UPS)
• Isolated IGBT/Power MOSFET gate drive




Pinout






Specifications

• Able to drive wide range of MOSFET/ IGBT without additional amplification
• Allows for smaller magnetic components - save board space
• Faster response time, overall higher system speed
• Meet International Safety Standards

Parameter	Symbol	Min	Max	Unit	Note
Storage Temperature	TS	-55	+125
Junction Temperature	Tj	-40	+125
Average Input Current	IF(AVG)		25	mA	1
Peak Transient Input Current (<1s pulse width, 300 pps)	IF(TRAN)		1.0	A
Reverse Input Voltage	VR		5	V
"High" Peak Output Current	IOH(PEAK)		2.5	A	2
"Low" Peak Output Current	IOL(PEAK)		2.5	A	2
Supply Voltage	VCC - VEE	-0.5	25	V
Output Voltage	VO(PEAK)	0	VCC	V
Output Power Dissipation	PO		250	mW	3
Total Power Dissipation	PT		296	mW	4
Lead Solder Temperature	+260 for 10 sec., 1.6 mm below seating plane
Solder Reflow Temperature Profile	See Package Outline Drawings section

Notes:
1. Derate linearly above +70 free air temperature at a rate of 0.3 mA/.
2. Maximum pulse width = 10 us, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I_O peak
minimum = 2.0 A. See Application section for additional details on limiting I_OL peak.
3. Derate linearly above +70 , free air temperature at the rate of 4.8 mW/.
4. Derate linearly above +70 , free air temperature at the rate of 5.4 mW/. The maximum LED junction temperature should not exceed +125 .

Description

This HCPL-3180 consists of a GaAsP LED. The LED is optically coupled to an integrated circuit with a power stage. These optocouplers are ideally suited for high frequency driving of power IGBT and MOSFETs used in Plasma Display Panels, high performance DC/DC convertors and motor control invertor applications.

Parameters:

Technical/Catalog Information	HCPL-3180
Vendor	Avago Technologies US Inc.
Category	Isolators
Type	Gate Drive Optocoupler
Mounting Type	Through Hole
Package / Case	8-DIP
Packaging	Tube
Lead Free Status	Contains Lead
RoHS Status	RoHS Non-Compliant
Other Names	HCPL 3180 HCPL3180