HCPL-2202

Current Transfer Ratio :
Maximum Input Diode Current :
Maximum Reverse Diode Voltage : 5 V
Minimum Operating Temperature : - 40 C
Packaging : Tube
Maximum Forward Diode Voltage : 1.7 V
Maximum Operating Temperature : + 85 C
Package / Case : PDIP-8
Maximum Baud Rate : 5 MBps
Maximum Power Dissipation : 210 mW


Features:

• 10 kV/ms Minimum Common Mode Rejection (CMR) at VCM = 1000 V (HCPL-2211/2212/0211/ 2232, HCNW2211)
• Wide Operating VCC Range: 4.5 to 20 Volts
• 300 ns Propagation Delay Guaranteed over the Full Temperature Range
• 5 Mbd Typical Signal Rate
• Low Input Current (1.6 mA to 1.8 mA)
• Hysteresis
• Totem Pole Output (No Pullup Resistor Required)
• Available in 8-Pin DIP, SOIC-8, Widebody Packages
• Guaranteed Performance from -40°C to 85°C
• Safety Approval UL Recognized -2500 V rms for 1 minute (5000 V rms for 1 minute for HCNW22XX) per UL1577 CSA Approved VDE 0884 Approved with VIORM = 630 V peak (HCPL- 2211/2212 Option 060 only) and VIORM = 1414 V peak (HCNW22XX only)
• MIL-STD-1772 Version Available (HCPL-52XX/62XX)




Application

• Isolation of High Speed Logic Systems
• Computer-Peripheral Interfaces
• Microprocessor System Interfaces
• Ground Loop Elimination
• Pulse Transformer Replacement
• High Speed Line Receiver
• Power Control Systems




Pinout






Specifications

Parameter		Symbol	Minimum	Maximum	Units	Note
Storage Temperature		TS	-55	125	°C
Operating Temperature		TA	-40	85	°C
Average Forward Input Current		I F(AVG)		10	mA	1
Peak Transient Input Current ( 1 ms Pulse Width, 300 pps) (£ 200 ms Pulse Width,< 1% Duty Cycle)	HCNW22XX	IF(tran)		1.0	A	1
				40	mA
Reverse Input Voltage	HCNW22XX	VR		5	V
				3
Average Output Current		IO		25	mA	1
Supply Voltage		VCC	0	20	V
Output Voltage		VO	-0.5	20	V	1
Total Package Power Dissipation	HCPL-223X	PT		210	mW	2
				294
Output Power Dissipation		PO	See Figure 7			1
Lead Solder Temperature (Through Hole Parts 260°C for 10 sec., Only)	HCNW22XX	260°C for 10 sec., 1.6 mm below seating plane
		260°C for 10 sec., up to seating plane
Solder Reflow Temperature Profile		See Package Outline Drawings section

Description

The HCPL-2202 is a optically-coupled logic gate. It contains an GaAsP LED. The detectors have totem pole output stages and optical receiver input stages with built-in Schmitt triggers to provide logic-compatible waveforms, illuminating the need for additional waveshaping.

The electrical and switching characteristics of the HCPL-2202 is guaranteed from -40 degrees C to 85 degrees C and a VCC from 4.5 volts to 20 volts. Low IF and wide VCC range allows compatibility with TTL, LSTTL, and CMOS logic and result in lower power consumption compared to other high speed couplers. Logic signals are transmitted with a typical propagation delay of 150 ns.

Parameters:

Technical/Catalog Information	HCPL-2202
Vendor	Avago Technologies US Inc.
Category	Isolators
Mounting Type	Through Hole
Package / Case	8-DIP
Isolation Voltage	3750Vrms
Configuration	1, One Direction
Input Type	DC
Output Type	Push-Pull, Totem-Pole
Data Rate	5Mbs
Current - Output/Channel	25mA
Packaging	Tube
Lead Free Status	Contains Lead
RoHS Status	RoHS Non-Compliant
Other Names	HCPL 2202 HCPL2202 516 1058 5 ND 51610585ND 516-1058-5