Features: • Separate Independent Read and Write data ports
- Supports concurrent transactions
• 300-MHz clock for high bandwidth
• 4-Word Burst for reducing address bus frequency
• Double Data Rate (DDR) interfaces on both Read and Write ports (data transferred at 600MHz) at 300 MHz
• Two input clocks (K and K) for precise DDR timing
- SRAM uses rising edges only
• Two input clocks for output data (C and C) to minimize clock-skew and flight-time mismatches
• Echo clocks (CQ and CQ) simplify data capture in high-speed systems
• Single multiplexed address input bus latches address inputs for both Read and Write ports
• Separate Port Selects for depth expansion
• Synchronous internally self-timed writes
• Available in x 8, x 9, x 18, and x 36 configurations
• Full data coherency providing most current data
• Core VDD = 1.8 (±0.1V); I/O VDDQ = 1.4V to VDD
• Available in 165-ball FBGA package (13 x 15 x 1.4 mm)
• Offered in both lead-free and non-lead free packages
• Variable drive HSTL output buffers
• JTAG 1149.1 compatible test access port
• Delay Lock Loop (DLL) for accurate data placementSpecifications(Above which the useful life may be impaired.)
Storage Temperature .................................65°C to +150°C
Ambient Temperature with Power Applied ...10°C to +85°C
Supply Voltage on VDD Relative to GND........... 0.5V to +2.9V
DC Applied to Outputs in High-Z ............0.5V to VDDQ + 0.3V
DC Input Voltage[15] ............................ 0.5V to VDDQ + 0.3V
Current into Outputs (LOW)........................................... 20 mA
Static Discharge Voltage (MIL-STD-883, M. 3015)...... > 2001V
Latch-up Current...................................................... > 200 mADescriptionThe CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 are 1.8V Synchronous Pipelined SRAMs, equipped with QDR™-II architecture. QDR-II architecture consists of two separate ports to access the memory array. The Read port has dedicated Data Outputs to support Read operations and the Write port has dedicated Data Inputs to support Write operations. QDR-II architecture has separate data inputs and data outputs to completely eliminate the need to "turn-around" the data bus required with common I/O devices. Access to each port is accomplished through a common address bus. Addresses for Read and Write addresses are latched on alternate rising edges of the input (K) clock. Accesses to the QDR-II Read and Write ports of CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 are completely independent of one another. In order to maximize data throughput, both Read and Write ports are equipped with Double Data Rate (DDR) interfaces. Each address location is associated with four 8-bit words (CY7C1311BV18) or 9-bit words (CY7C1911BV18) or 18-bit words (CY7C1313BV18) or 36-bit words (CY7C1315BV18) that burst sequentially into or out of the device. Since data of CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 can be transferred into and out of the CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 on every rising edge of both input clocks (K and K and C and C), memory bandwidth is maximized while simplifying system design by eliminating bus "turn-arounds".
Depth expansion of CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 is accomplished with Port Selects for each port. Port selects allow each port to operate independently.
All synchronous inputs of CY7C1311BV18, CY7C1911BV18, CY7C1313BV18, and CY7C1315BV18 pass through input registers controlled by the K or K input clocks. All data outputs pass through output registers controlled by the C or C (or K or K in a single clock domain) input clocks. Writes are conducted with on-chip synchronous self-timed write circuitry.
CY7C1315BV18 Data Sheet
