Features: `High Input Sensitivity IFT = 1.0 mA
`ITRMS = 300 mA
`High Static dv/dt 10,000 V/s
`Electrically Insulated between Input and Output circuit
`Microcomputer compatible
`Trigger Current
- (IFT < 1.2 mA) BRT22F, BRT23F,
- (IFT < 2 mA) BRT21H, BRT22H, BRT23H
- (IFT < 3 mA) BRT21M, BRT22M, BRT23M
`Available Surface Mount and on on tape and reel
`Zero Voltage Crossing detector
`UL File E52744 System Code "J"
`Lead-free component
`Component in accordance to RoHS 2002/95/EC and WEEE 2002/96/EC
Application·Industrial controls
·Office equipment
·Consumer appliancesPinout
SpecificationsTamb = 25, unless otherwise specifie Stresses in excess of the absolute Maximum Ratings can cause permanent damage to the device. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute Maximum Rating for extended periods of the time can adversely affect reliability.
Input
| Parameter |
Test condition |
Symbol |
Value |
Unit |
| Reverse voltage |
IR= 10 A |
VR |
6.0 |
V |
| Forward current |
|
IF |
60 |
mA |
| Surge current |
|
IFSM |
2.5 |
A |
| Power dissipation |
|
Pdiss |
100 |
mW |
| Derate from 25 |
|
|
1.33 |
mW/ |
Output
| Parameter |
Test condition |
Part |
Symbol |
Value |
Unit |
| Peak off-state voltage |
ID(RMS)= 70 A |
BRT21 |
VDM |
400 |
V |
| BRT22 |
VDM |
600 |
V |
| BRT23 |
VDM |
800 |
V |
| RMS on-state current |
|
|
ITM |
300 |
mA |
| Single cycle surge current |
|
|
|
3.0 |
A |
Power dissipation |
|
|
Pdiss |
600 |
mW |
| Derate from 25 |
|
|
|
6.6 |
mW/ |
Coupler
| Parameter |
Test condition |
Symbol |
Value |
Unit |
Isolation test voltage (between
emitter and detector, climate per
DIN 500414, part 2, Nov. 74) |
t = 1.0 min. |
VISO |
5300 |
V
RMS |
| Pollution degree (DIN VDE 0109) |
|
|
2 |
|
| Creepage |
|
|
7.0 |
mm |
| Clearance |
|
|
7.0 |
mm |
Comparative tracking index per DIN IEC 112/VDE 0303 part 1,
group IIIa per DIN VDE 6110 |
|
|
175 |
|
| Isolation resistance |
VIO = 500 V, Tamb = 25 |
RIO |
1210 |
|
| VIO = 500 V, Tamb = 100 |
RIO |
1011 |
|
| Storage temperature range |
|
Tstg |
- 55 to + 150 |
|
| Ambient temperature range |
|
Tamb |
- 55 to + 100 |
|
| Soldering temperature |
max. 10 sec. dip soldering 0.5 mm from case bottom |
Tsld |
260 |
|
DescriptionThe BRT21, BRT22, BRT23 product family consists of AC switch optocouplers with zero voltage detec- tors with two electrically insulated lateral power ICs which integrate a thyrister system, a photo detector and noise suppression at the output and an IR GaAs diode input
High input sensitivity of BRT22 is achieved by using an emitter follower phototransistor and an SCR predriver result- ing in an LED trigger current of less than 2 mA or 3 mA (DC). Inverse parallel SCRs provide commutating dv/dt greater than 10 kV/s
The zero cross line voltage detection circuit consists of two MOSFETS and a photodiode. THe BRT21/ 22/ 23 product family isolates low-volt- age logic from 120, 230 and 380 VAC lines to control resistive, inductive or capacitive loads including motors, solenoids, high current thyristers or TRIAC and relays.
BRT22 Data Sheet
