Features: ` Software command-set compatible with JEDEC 42.4 standard- Backward compatible with Am29F and Am29LV families` CFI (Common Flash Interface) complaint- Provides device-specific information to the system, allowing host software to easily reconfigure for different Flash...
Am29PDL128G: Features: ` Software command-set compatible with JEDEC 42.4 standard- Backward compatible with Am29F and Am29LV families` CFI (Common Flash Interface) complaint- Provides device-...
SeekIC Buyer Protection PLUS - newly updated for 2013!
268 Transactions
All payment methods are secure and covered by SeekIC Buyer Protection PLUS.
` Software command-set compatible with JEDEC 42.4 standard
- Backward compatible with Am29F and Am29LV families
` CFI (Common Flash Interface) complaint
- Provides device-specific information to the system, allowing host software to easily reconfigure for different Flash devices
` Erase Suspend / Erase Resume
- Suspends an erase operation to allow read or program operations in other sectors of same bank
` Unlock Bypass Program command
- Reduces overall programming time when issuing multiple program command sequences
Storage Temperature
Plastic Packages . . . . . . . . . . . .65°C to +150°C
Ambient Temperature
with Power Applied. . . . . . . . . . 65°C to +125°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . .0.5 V to +4.0 V
A9, OE#, RESET#, and ACC
(Note 2) . . . . . . . . . . . . . . . . . . . .0.5 V to +12.5 V
All other pins (Note 1) . . . . . . 0.5 V to VCC +0.5 V
Output Short Circuit Current (Note 3) . . . . . .200 mA
Notes:
1. Minimum DC voltage on input or I/O pins is 0.5 V. During voltage transitions, input or I/O pins may overshoot VSS to 2.0 V for periods of up to 20 ns. Maximum DC voltage on input or I/O pins is VCC +0.5 V.See Figure 7. During voltage transitions, input or I/O pins may overshoot to VCC +2.0 V for periods up to 20 ns. See Figure 8.
2. Minimum DC input voltage on pins A9, OE#, RESET#, and ACC is 0.5 V. During voltage transitions, A9, OE#, ACC, and RESET# may overshoot VSS to 2.0 V for periods of up to 20 ns. See Figure 7. Maximum DC input voltage on pin A9, OE#, RESET#, and ACC is +12.5 V which may overshoot to +14.0 V for periods up to 20 ns.
3. No more than one output may be shorted to ground at a time. Duration of the short circuit should not be greater than one second.
Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this data sheet is not implied.
Exposure of the device to absolute maximum rating conditions for extended periods may affect device reliability.
The Am29PDL128G is a 128 Mbit, 3.0 volt-only Page Mode and Simultaneous Read/Write Flash memory device organized as 8 Mwords or 4 M double words (One word is equal to two bytes). The device is offered in an 80-ball Fortified BGA package. The word-wide data (x16) appears on DQ15-DQ0; the double word mode data (x32) appears on DQ31-DQ0. This device can be programmed in-system or in standard EPROM programmers. A 12.0 V VPP is not required for write or erase operations.
Am29PDL128G offers fast page access times of 25 and 30 ns, with corresponding random access times of 70 and 80 ns,respectively, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls.