6N140A

Isolation Voltage :
Packaging :
Maximum Operating Temperature : + 125 C
Maximum Forward Diode Voltage : 1.8 V
Maximum Reverse Diode Voltage : 5 V
Output Type : Open Collector
Maximum Propagation Delay Time : 100 us
Maximum Forward Diode Current : 5 mA
Maximum Continuous Output Current : 40 mA
Maximum Power Dissipation : 200 mW
Minimum Operating Temperature : - 55 C
Package / Case : PDIP-16


Features:

• Dual Marked with Device Part Number and DSCC Drawing Number
• Manufactured and Tested on a MIL-PRF-38534 Certified Line
• QML-38534, Class H and K
• Five Hermetically Sealed Package Configurations
• Performance Guaranteed, Over -55 to +125
• Low Input Current Requirement: 0.5 mA
• High Current Transfer Ratio: 1500% Typical @I_F = 0.5 mA
• Low Output Saturation Voltage: 0.11 V Typical
• 1500 Vdc Withstand Test Voltage
• High Radiation Immunity
• 6N138/9, HCPL-2730/31 Function Compatibility
• Reliability Data




Application

• Military and Space
• High Reliability Systems
• Telephone Ring Detection
• Microprocessor System Interface
• Transportation, Medical, and Life Critical Systems
• Isolated Input Line Receiver
• EIA RS-232-C Line Receiver
• Voltage Level Shifting
• Isolated Input Line Receiver
• Isolated Output Line Driver
• Logic Ground Isolation
• Harsh Industrial Environments
• Current Loop Receiver
• System Test Equipment Isolation
• Process Control Input/Output Isolation




Pinout






Specifications

Storage Temperature Range, T_S ............................... -65 to +150
Operating Temperature, T_A ....................................... -55 to +125
Case Temperature, T_C ............................................................ +170
Junction Temperature, T_J ........................................................ +175
Lead Solder Temperature ............................................. 260 for 10s
Output Current, I_O (Each Channel)............................................40 mA
Output Voltage, V_O (Each Channel) ............................. -0.5 to 20 V^[1]
Supply Voltage, V_CC ..................................................... -0.5 to 20 V^[1]
Output Power Dissipation (Each Channel) ........................... 50 mW^[2]
Peak Input Current (Each Channel, <1 ms Duration) .................20 mA
Average Input Current, I_F (Each Channel) ............................ 10 mA^[3]
Reverse Input Voltage, V_R (Each Channel) ......................................5V
Package Power Dissipation, P_D (each channel) .......................200 mW

Notes:
1. GND Pin should be the most negative voltage at the detector side. Keeping V_CC as low as possible, but greater than 2.0 V, will provide lowest total I_OH over temperature.
2. Output power is collector output power plus total supply power for the single channel device. For the dual channel device, output power is collector output power plus one half the total supply power. For the quad channel device, output power is collector output power plus one fourth of total supply power. Derate at 1.66 mW/ above 110.
3. Derate IF at 0.33 mA/ above 110.




Description

The 6N140A is a commercial grade four channel hermetically sealed optocoupler in a 16-Pin ceramic DIP package with gold plated leads. Solder dipped leads and various lead form options are also available. See the datasheet for details.
The product is capable of operation and storage over the full mil temp range and may also be purchased with full MIL-PRF-38534 Class H or K level testing, or from the appropriate DSCC SMD (83024 for Class H, 5962-98002 for Class K). The 6N140A is manufactured and tested on a MIL-PRF-38534 certified line and Class H and K versions are included in the DSCC Qualified Manufacturers List QML-38534 for Hybrid Microcircuits.
Each channel of 6N140A contains a GaAsP light emitting diode which is optically coupled to an integrated high gain photon detector. The high gain output stage features an open collector output providing both lower saturation voltage and higher signaling speed than possible with conventional photo-Darlington optocouplers. The shallow depth and small junctions offered by the IC process provides better radiation immunity than conventional photo transistor optocouplers.
The supply voltage of 6N140A can be operated as low as 2.0 V without adversely affecting the parametric performance. These devices have a 300% minimum CTR at an input current of only 0.5 mA making them ideal for use in low input current applications such as MOS, CMOS, low power logic interfaces or line receivers. Compatibility with high voltage CMOS logic systems is assured by specifying Icch and Ioh at 18 Volts.
Package styles of 6N140A available for this die set with one, two or for channels are 8 and 16-Pin DIP through hole, 16-Pin surface mount DIP flat pack, and 20 pad leadless ceramic chip carrier. Most devices may be purchased with a variety of lead forms and plating options. See datasheet for details.
Because the same electrical die (emitters and detectors) are used for each channel of each device listed in the datasheet, absolute maximum ratings, recommended operating conditions, electrical specificationsof 6N140A , and performance characteristics shown in the datasheet figures are virtually identical for all parts. Occasional exceptions exist due to package variations and limitations and are as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities give justification for the use of data obtained from one part to represent other parts performance for reliability and certain limited radiation test results.

The 6N140A is single, dual, and quad channel, hermetically sealed optocouplers. The products are capable of operation and storage over the full military temperature range and can be purchased as either standard product or with full MIL-PRF-38534 Class Level H or K testing or from the appropriate DSCC Drawing. All devices are manufactured and tested on a MIL-PRF-38534 certified line and are included in the DSCC Qualified Manufacturers List QML- 38534 for Hybrid Microcircuits.

Each channel contains a GaAsP light emitting diode which is optically coupled to an integrated high gain photon detector. The high gain output stage features an open collector output providing both lower saturation voltage and higher signaling speed than possible with conventional photo-Darlington optocouplers. The shallow depth and small junctions offered by the IC process provides better radiation immunity than conventional photo transistor optocouplers.

The supply voltage of 6N140A can be operated as low as 2.0 V without adversely affecting the parametric performance.

The 6N140A has a 300% minimum CTR at an input current of only 0.5 mA making them ideal for use in low input current applications such as MOS, CMOS, low power logic interfaces or line receivers. Compatibility with high voltage CMOS logic systems is assured by specifying ICCH and IOH at 18 Volts.

Upon special request, the following 6N140A selections can be made: CTR minimum of up to 600% at 0.5 mA, and lower output leakage current levels to 100 mA.Package styles for these parts are 8 and 16 pin DIP through hole (case outlines P and E respectively), 16 pin DIP flat pack (case outline F), and leadless ceramic chip carrier (case outline 2).Devices may be purchased with a variety of lead bend and plating options. See Selection Guide table for details. Standard Military Drawing (SMD) parts are available for each package and lead style.

Because the same electrical die (emitters and detectors) of 6N140A are used for each channel of each device listed in this data sheet, absolute maximum ratings, recommended operating conditions, electrical specifications, and performance characteristics shown in the figures are similar for all parts except as noted. Additionally, the same package assembly processes and materials are used in all devices. These similarities justify the use of a common data base for die related reliability and certain limited radiation test results.

Parameters:

Technical/Catalog Information	6N140A
Vendor	Avago Technologies US Inc.
Category	Isolators
Voltage - Isolation	-
Input Type	DC
Output Type	Darlington with Base
Current - Output / Channel	40mA
Voltage - Output	20 V
Vce Saturation (Max)	100mV
Current Transfer Ratio (Min)	1500% @ 5mA
Mounting Type	Through Hole
Package / Case	16-DIP
Packaging	Tube
Number of Circuits	1 - Single
Lead Free Status	Lead Free
RoHS Status	RoHS Compliant
Other Names	6N140A 6N140A 516 1834 5 ND 51618345ND 516-1834-5