Position: Home > Circuit Diagram > power supply circuit > Index 189

Low Cost Custom Prototype PCB Manufacturer

power supply circuit

Index 189

Rechargeable flashlight circuit one (4)

Published:2011/7/15 0:44:00 Author:TaoXi | Keyword: Rechargeable, flashlight

Rechargeable flashlight circuit one (4)
(View)

View full Circuit Diagram | Comments | Reading(1449)

LM317 Current-Expansion Circuit (2)

Published:2011/7/16 6:29:00 Author:Robert | Keyword: Current, Expansion

The picture shows the LM317 current-expansion circuit (2). This circuit is also OK. But its output voltage may be unstable. Because the LM317's pin 1-2 is the reference voltage and the output voltage would minus the power transistor's B-E junction voltage. Not only this, the B-E junction voltage also would decrease while the transistor's temperature increasing. So the output voltage mey be unstable and it's not recommended to do this. (View)

View full Circuit Diagram | Comments | Reading(4908)

LM317 Current-Expansion Circuit (1)

Published:2011/7/16 7:42:00 Author:Robert | Keyword: Current, Expansion

The picture shows the LM317 current-expansion circuit (1). The input voltage is VIN. The Q1 needs a large-enough heatsink. The Q2 needs a adequate heatsink. The output voltage is 1.25V-15V/5A. (View)

View full Circuit Diagram | Comments | Reading(3098)

The inverter circuit 1

Published:2011/7/16 4:17:00 Author:Christina | Keyword: inverter

The inverter circuit 1
(View)

View full Circuit Diagram | Comments | Reading(1181)

The inverter circuit 10

Published:2011/7/16 4:17:00 Author:Christina | Keyword: inverter

The inverter circuit 10
(View)

View full Circuit Diagram | Comments | Reading(3826)

[165V.HID.PWM] half bridge driver module

Published:2011/7/16 4:01:00 Author:Christina | Keyword: half bridge, driver module

[165V.HID.PWM] half bridge driver module
(View)

View full Circuit Diagram | Comments | Reading(2961)

Ringing type switching power supply constant current driving circuit

Published:2011/7/15 23:18:00 Author:Christina | Keyword: Ringing type, switching, power supply, constant current, driving circuit

In the ringing type switching power supply, the power loss of the driving circuit which supplies the base current to the switching transistor is very large. The voltage UB of the transformer coil NB must ensure the minimum input voltage of the switching transistor to make the fully conduction, and the voltage UB is proportional to the input voltage Vi. When the Vi increases, the driving current Id will increases too, but the base resistance Rb increases the power loss that has the square relationship with the increasing part of Id. When the driving current ID is increasing, the voltage stabilization diode subcircuit current will increase too, and this will cause the oscillation problem, in a certain period of time, the switch works, and in the next period of time, the switch stops working. (View)

View full Circuit Diagram | Comments | Reading(618)

Ringing type switch power supply power expansion method

Published:2011/7/15 22:54:00 Author:Christina | Keyword: Ringing type, switch, power supply, power expansion

Ringing type switch power supply power expansion method
In the simple ringing current-limit power supply circuit, in order to make the output voltage stable, we need to connect the voltage-regulator diode with the base electrode of the switching transistor VTl, so the output voltage can not be adjusted. In addition, if you want to increase the output power, you need to increase the driving current. At this time, if you decrease the output current, the subcircuit current of the voltage-regulator diode will increase. This will change the voltage stabilization value of the voltage stabilization diode, even more than the allowable value of the voltage stabilization diode. So in order to improve the output power, we can use the method of add a current expansion transistor which is as shown in the figure. (View)

View full Circuit Diagram | Comments | Reading(567)

Ringing switching power supply practical circuit

Published:2011/7/15 22:44:00 Author:Christina | Keyword: Ringing, switching power supply, practical circuit

The ringing switching power supply practical circuit is as shown in the figure. The primary winding Np of the transformer is connected with the diode VD, the resistance R and capacitance C, the purpose of this connection method is to release the power of the transformer leakage inductance. That is during the conduction of the switching tube, the current accumulates the power on the leakage inductance, but this power is not transfered to the secondary stage of the transformer as the electric power. So it produces the reverse emf when the switching tube is cutting off, there is the high surge voltage to puncture the switching tube. (View)

View full Circuit Diagram | Comments | Reading(956)

The method to change the output voltage of the ringing switch power supply

Published:2011/7/15 22:22:00 Author:Christina | Keyword: method, output voltage, ringing switch, power supply

The method to change the output voltage of the ringing switch power supply
In the simple ringing current-limit type switching voltage stabilization circuit, the output voltage Vo is proportional to the negative bias Uc. If you want to change the output voltage, you need to change the Uc, as shown in the figure. The collector electrode of the transistor VT2 is connected with the negative terminal of the capacitor C2. Once the Uc2 rises, the current which flows through the zener diode VD2 and the transistor VT2 will increase to conduct VT2. Because the collector electrode current of VT2 shortens the conduction time of the switching transistor VT1, so we can cut off the circuit in advance to reduce the output voltage Vo. (View)

View full Circuit Diagram | Comments | Reading(596)

Dual polarity voltage stabilizer with the three-port voltage stabilizer

Published:2011/7/16 5:52:00 Author:Christina | Keyword: Dual polarity, voltage stabilizer, three-port, voltage stabilizer

Dual polarity voltage stabilizer with the three-port voltage stabilizer
(View)

View full Circuit Diagram | Comments | Reading(573)

The inverter circuit 14

Published:2011/7/16 4:26:00 Author:Christina | Keyword: inverter

The inverter circuit 14

Data: base coil 8-10 turns (two groups), Primary coil 18-24 turns (two groups), Subprime coil600-800 turns, the high power relay. The 39 and 2.7ohms resistabce is 2-4W; the 6uF capacitance's voltage is 1000V. (View)