Flickering Light Ⅱ

Published:2011/8/11 22:45:00 Author:Amy From:SeekIC

Robert Edlinger



In the July/August 2004 issue we pub­lished a flickering light for use in models that uses a microcontroller to minimize the component count. Regardless of whether you want to effectively imitate a house fire, a campfire, or light from welding, the circuit described here fills the bill without using a microcontroller, although it does use a larger number of components (including some truly uncommon ones).

The circuit is based on three oscillators, which are built using unijunction transis­tors (UJTs). Each oscillator has a different frequency. The output voltages are mixed, which produces the flickering effect.

A unijunction transistor consists of an n-type bar of silicon between two ohmic (non-barrier) base contacts (Bl and B2). The effective resistance is controlled by the p-type emitter region. The designation ’transistor’ is a somewhat unfortunate choice, since it cannot be used for linear amplification. UJTs are suitable for use as pulse generators, monostable multivibra­tors, trigger elements and pulse-width modulators. If a positive voltage is applied to the emitter (E), the capacitor charges via the resistor. As soon as the voltage on the emitter reaches approxi­mately half the supply voltage (for a 2N2645, the value lies in the range of 56-75 %), the UJT ’fires’ and the capac­itor discharges via base Bl and the resis­tor, generating a positive pulse. The UJT then returns to the non-conduct state, and the process just described repeats period­ically. The frequency can be approxi­mately given by the formula

f=l/(RC)

The frequency is independent of the value of the supply voltage (which must not exceed 35 V). The maximum emitter blocking voltage is 30 V, and the maxi­mum permissible emitter current is 50 mA. The values of resistors Rl, R2 and R3 can lie between 3 kΩ and 500 kΩ. If neces­sary, the frequency can be varied over a range of 100:1 by using a trimpot instead of a fixed resistor.

The frequencies from the three pulse gen­erators are mixed by connecting them to the IR diode of a triac optocoupler via R4. The optocoupler, a type MOC3020, K3030P or MCP3020, can handle a maximum load current of 100 mA. The triac triggers at irregular intervals and generates the desired flickering light in the two small lamps, LI and L2, which are connected in series to the transformer secondary.

The light effect can be noticeably improved by using a MOC3040, which contains a zero-voltage switch, since it s generates irregular pauses of various lengths when suitable frequencies occur in the individual oscillators. The zero-volt­age switch does not switch while the cur­rent is flowing, but only when the applied ac voltage posses through zero. An inte­grated drive circuit (zero crossing unit) allows full half-waves or full cycles to pass (pulse-burst control) Due to the flickering effect arising from its switching behaviour, it is not suitable for normal lighting, but here this just what we want. This version of the optocoupler is also designed for a maximum current of 100 mA.

For a small roof fire or the light of a weld­ing torch in a workshop, two small incan­descent lamps connected in series and rated at 6 V / 0.6 A (bicycle taillight bulbs) or a single 12-V lamp (rated at 100 mA) is adequate. If it is desired to simulate a large fire, a triac (TIC206D, rated at 400 V / 4 A, with a trigger cur­rent of 5 mA) can be connected to the out­put of the circuit and used to control a more powerful incandescent lamp.

As continuous flickering looses its attrac­tion for an interested observer after a while (since no house burns for ever, and welders also take breaks), it’s a good idea to vary the on and off times of the circuit. This is handled by a bipolar Hall switch (UE4935L), which has such a small package that it can fitted between the sleepers of all model railway gauges, including Miniclub (Z Gauge), or even placed alongside the track if a strong per­manent magnet is used. If a magnet is fixed somewhere on the base of a loco­motive such that the south pole points toward the package of the Hall switch (the flattened front face with the type marking), the integrated npn transistor will switch on and pull the base of the exter­nal pnp transistor negative, causing the collector-emitter junction to conduct and provide the necessary ’juice’ for the uni­junction transistors. If another traction unit whose magnet has it s north pole point­ing toward the Hall switch passes a while later, the switch will be cut off and the flickering light will go out. Of course, you can also do without this form of trigger­ing and operate the device manually.

Reprinted Url Of This Article: http://www.seekic.com/blog/project_solutions/2011/08/11/Flickering_Light_Ⅱ.html

Print this Page | Comments | Reading(1298)